FWS223RFS2 Frigidaire Washer - Instructions

carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.

First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.

The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!

The problem with my very old washer was that the tension spring had broken long ago and I had jerry-rigged it in place with a cable tie. It would work, but you had to give the drum a spin by hand when it hit the spin the cycle. This probelm further caused the premature wearing of the drive belt, due to slippage. I ordered both a new spring and a new belt. Upon their arrival, I removed the two screws holding the front panel and lowered it off and out of the way. The old, worn belt was very easy to remove, as there was very little tension on it. Next I attempted to remove the washer that holds the idle arm on. It is in a very awkward spot, and it appears the the washing machine is sort of built around it. I bent it gradually with locking pliers until I could force it off with the blade of a flat screwdriver. Then the idler arm was easy to lower of its axle by twisting the drum a bit and pulling it to one side. I put the new spring into the idler arm, making sure the plastic bushing was in place and replaced the arm. I then repositioned to belt and replaced the front panel. It works great now.

Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.

Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.

Very happy camper here!

pulled old knob off. pushed new knob on.

Unplugged machine.
Turned off water supply.

Removed front panel.
Pushed in on belt tensioner, removed old belt, replaced with new belt.

Used pry bar to lift the base assembly high enough off the snubber to remove it. Partially propped it with 2x4 wood scraps.

Used bent clothes hangar to remove old snubber ring, to protect my hands.

Replaced snubber, arrow pointing up.
Carefully lowered base assembly.

Replaced front panel.
Turned water back on, plugged back in, washing machine no longer 'walks'.

Remember to check the washer against a level if you moved the machine.

removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!

fast shipping too! will recommend others!

This is the third time I have ordered parts from this company .I can't say enough good things about them from their fast shipping( always arrives sooner than they state)To the quality of the parts and the shipping packages.A first class operation from start to finnish.First step was to disconect power supply.Second was to remove washer drain hose from house drain.Third remove two (2) phillips head screws from front cover of washer ,located at bottom right and left side of front panel near floor.Lift front panel up to unhook metal retainers on panel that connect it to washer side panels.Use pliers to remove spring clamp from hose. Remove hose from washer pump. Remove clamp from hose,remove plastic retainer holding hose to washer bottom.Feed hose out the back of the washer through washer drain hose hole in the back pannel of the washer.Remove plastic retainer.Insert the new hose through the hole in the back pannel install the hose clamp and install the hose back on the pump.Relocate clamp on hose, take front panel,lift into place,push down to lock retaining taps into side cover slots replace the two phillips head screws.

first removed the 2 screws disconected the terminals, installed new switch connected wires back and test washer and it worked like new, i put a Jumper to get the washer to work while i got the parts. Also i received the parts in 24 hrs. Thank You.

i took out the two back screws lift the top.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.

Received lid lock within 24 hours, fixed washer within 10 minutes...up and running. Thanks.

Removed 2 screws at bottom of the front panel - removed front panel by sliding the panel down about 1/2 inch and then away from the appliance- v belt is removed by pushing the tensioner pulley to remove tension from the belt and turning the pulley untill the belt is removed instalation is a simple reverse of the process. I did't have a repair manual so every step was trial and error untill I was able to complete the repair.

I got online and figured out exactly how to take off the front of the washer and then how to replace the belt. It was so easy. The part itself arrived much sooner than predicted. It fit perfectly and my washing machine is now running smoothly and quietly.

My washing machine stopped agitating and spinning and I couldn't afford a repair man...plus I wanted to exhaust any obvious problems first. One of the leveler feet had broken years ago. Since I luckily had determined via reading other posts that the agitator won't work if the cycle safety switch is not functioning right, I thought the safety switch might need to be changed but after careful thought, I decided to order a new levelling leg first because maybe the broken levelling leg was shaking the safety switch so it wasn't connecting right. Once I received the leg overnight, I flipped the washer on its side and had to drill out the old leg. It was a little tricky because of how it broke, but the drill worked. I flipped the washer back up, leveled it with the new foot, and the agitator was miraculously working again...just like new. I didn't need the safety switch. Thanks to partselect.com for having the details of my washer parts to study up on and get me the right part so quickly. I saved myself alot of money.