FTF2140ES0 Frigidaire Washer - Instructions

The repair itself was simple; it was the original design of the washer itself that made it time-consuming, because of the tight spaces involved. Basically, all you have to do is remove 2 plastic pins, take out the broken part, make sure you have the new part facing the right way, and put the 2 plastic pins back in. Should take 2 minutes if there are not other machine parts in the way!

First I removed the visible screws on the front of control panel. When I tried to remove it I realized it was also being held in place by the top coverof the washer. I next removed the screws holding the top cover in place and slid it back uncovering a few more screws holding the control console in place. The wiring pane was also held on the console with screws so i roved them and popped the old console out. After that I just replaced everything in reverse order and screwed the new console back in place. The door handle was alot more simpler. All I did there was open the door and remove the two visible screws on the inside of the door and the broken handle came off. I placed the new handle in place and screwed it on. These repairs were simple and once done I realized that it took no time at all.

first removed top of machine. removed 3 valve core wires set. Then removed left top screw on valve. Then removed vent tube to get to lower right screw. disconnected hose connect rack so valve housing could be removed & new installed. Rapped insulation around valve & installed. Put everything back together in reverse order.

I watched the u-tube video and followed what he did and it was fixed. Reason it took over 15 min I had to find the correct bit for the screw. I think your web site is great thanks

Open the door. Pull the clamp off of the boot (locate spring at bottom). Peel back the boot on the right side so that you can get to the door lock and switch assy. Remove the 2 screws in the front that hold in the door lock and switch assy. Remove the wires from the old assy. Transfer the wires to the new assy. Screw in the new assy. Refit the boot and clamp. give it a try.

I unplugged it from the outlet, undid the two screws from the top, then slid it off, opened the door and undid the two screws from the door switch lifted it out relaced it with the new one, screwed it back into place, replaced the top, plugged it back in and away it went.
Garry

2 screws off and put new striker in and replaced the screws

My 10 yr old son removed the two screws, placed the new strike on, and screwed it back into place!! So easy a child did it!!

Very easy to fix. Diagram on web page was very helpful. Part was delivered over night. Great service.

I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affected part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."

PartSelect had the part in stock, shipped that day. The part was delivered the next day, my wife had it installed and working when I got home from work.

after clearing shelving. It took about 20 minutes to remove the dryer stacked on top, along with the gas line and the vent hose.....
Two screws and gently pry the back up with a screwdriver and the top pops off. open the door and remove the 2 screws while reaching down inside and the switch come right up with its 3 plug harness.
swap the old switch unit for the new one and slip it back down into place and reinstall the screws, and done in about 15 minutes.

my belt is in good shape so I will save the one I bought for later.
the handle is 2 screws and took less than 2 minutes.
It took about 20 minute to put the washer/dryer units back together and against the wall and running

-Unplug machine and remove all water connections
-Remove back panel with power phillips screwdriver
-Removed some rectangular circuit box in the way of getting to one shock absorber (3 screws)
-Remove old shock absorbers with 1/2 inch socket (suggested in accompanying directions)- this took 2 minutes
-inserted new shocks as directed...this was the most difficult part, but used a hammer to bang into place.
-reinsert and screw down circuit box (or whatever it was)
-reattach back panel
-reestablish water hose connections
-plugged in and was in business
-had ordered a washer/dryer set for $1700 (at my parent's urging) and now can tell Sears to go pound sand!

After accidentally dropping a crystal clock (don't ask) near the open door of the front-loading washer, the plastic striker broke and couldn't be repaired. Without this part being functional, the washer won't start because the door can't be secured.

I ordered the new part, and it arrived quickly -- that's really the story here.

Replacing it meant removing two screws, pulling the damaged part off, slapping the new part in, and replacing the screws. My 4th grade daughter could have done this one -- wish they were all that easy!

I'm glad the part came so quickly. With a local supplier, it would have taken four more days.

Removed broken Vane and reinstalled replacemnet real time repair 2 minutes. It took longer to open box than to fix.