Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FGHD2433KF1 > Instructions

FGHD2433KF1 Frigidaire Dishwasher - Instructions

All installation instructions for FGHD2433KF1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FGHD2433KF1
46-60 of 526
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the valve stuck closed - no water would enter the machine

  • Customer: Richard from Fox River Grove, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 9 of 12 people found this instruction helpful
remove vanity panel
disconnect copper supply line from valve
remove valve mounting screws
rotate valve to access hose clamp
loosen clamp and slide up rubber tubing about 2 inches
pull hose off barbed fitting and remove old valve
reverse order with new valve

leaking dishwasher

  • Customer: Mark from port matilda, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .

large holes in the bottom of the basket where pieces of plastic kept breaking off

  • Customer: Lauren from Peabody, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.

Upper spray arm fell/broke off

  • Customer: Sharon from Clinton Township, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
I researched the problem we had with our dishwasher and found the Parts Select website. My husband and I figured out how to remove the broken part and I selected and purchased the replacement.

The part was shipped quickly and when it arrived I changed the broken part with the replacement in less than five minutes. It seems to be working just fine.

I have added Parts Select to our "favorites" in case we have problems with any of our other appliances. Thanks Parts Select. :)

arm upper spray unit fell off

  • Customer: Randall from Mather, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
Easiest repair ever. Part came quickly & came fully assembled. Just screwed the part on by hand and it has worked like new ever since. The original part is 3 separate pieces but the new part was all in one & fit perfectly.

Leaky Dishwasher and broken spray arm

  • Customer: Jason from Hillsborough, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
Upper spray are assembly simply screws onto the threaded fitting of the inside ceiling of the dishwasher.

The bottom door gasket simply slides in place. both were done in less than 5 minutes. Be careful the gasket only goes in one way. But it is obvious what way it goes in.

A hole in the dishwasher dicharge hose.

  • Customer: Lee from Columbus, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 17 of 38 people found this instruction helpful
I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.

Replace sump gasket

  • Customer: Greg from Rockwall, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 13 of 27 people found this instruction helpful
#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

Dishwasher was leaking out of small gold nut

  • Customer: Emily from Kyle, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 7 of 9 people found this instruction helpful
The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

bottom spray arm was broken

  • Customer: Shaun from Greer, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 18 people found this instruction helpful
lift off yhe old one and snap on the new one

found spray arm on the rack

  • Customer: JOHN from LA QUINTA, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
found spray arm on the rack looked at the top of rack saw a nut screw the nut looked at the clip found the ears broke off easy r&r.

Left side door spring replacment

  • Customer: John from SIERRA VISTA, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
First thing I did was turn off the power to the dishwasher, then remove the racks. Remove the foot plates, remove the two top screws holding the dishwasher. Then using the socket set, retract the two foot stands to pull the dishwasher forward. You may not have to do this step as I had to get it over tile. The pully springs are on the sides, easily replaced. After replacing the springs and I recommend replacing both at the same time, put everything back. The hardest part will be the foot plates, there are two and getting them lined up and the screws back in is a bit of a challenge. Then you are done.

bottem door gasket was shot and leaked

  • Customer: Christine from Marne, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

Interior bottom door gasket seal broken

  • Customer: Philip from Freehold, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

Fence in dishwasher rack rusted

  • Customer: Michael from Katy, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 13 people found this instruction helpful
Unsnapped three clips in lower rack securing old fence in rack. Attached clips to new fence and snapped assembly back into rack.
All Instructions for the FGHD2433KF1
46-60 of 526