FEP310KW5 Roper Range - Instructions

Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.

Very easy . Just removed four screws and removed the back cover. Then just unplugged two clips from the element . The repeated all of my steps in reverse . Be sure to unplug the oven before you start on the project .

I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.

I discoverd my switch box locked with my stove electrical port and stove stopped functioning. Pulled my stove back and saw that the "terminal block" was melted on one side; hence, switch box locked in place to avoid a fire, thank goodness. Looked up part on internet, unplugged stove, took off terminal box, ordered part and replaced. BTW - PART SELECT is awesome; I received my part the very next day!!! :-) Very happy with their service.

I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

Purchased 2 piece broiler pan from this site

I just put the drip bowl in and plugged in the new heating element and I was done. It heats much faster and is level now so cooking is much easier. Also the parts arrived sooner than I expected, so I was very satisfied overall. Couldn't have been much easier all around. I will use Partselect.com in the future. Thanks

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is really easy to repair.

Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.

My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.