Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FEP310KW4 > Instructions

FEP310KW4 Roper Range - Instructions

All installation instructions for FEP310KW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310KW4
46-60 of 161
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Element had burned out, and the drawer glides were broken .

  • Customer: Allen from ASHLAND, PA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Replaced both .

element burned out shortly after purchase of range, one was purchased locally and did not fit properly, causing element to burn out

  • Customer: Sue from INDIANOLA, MS
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
replaced element with new one , worked perfectly-

Block had melted.R

  • Customer: Thomas H. from COCOA, FL
  • Difficulty: Very Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Removed old terminal block & replaced with new one. Very simple. Did NOT have to replace cover as stated you should. Shipping could have been a little faster. Will definetly try this site again.

screw came off

  • Customer: Sandeep from EDINA, MN
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
very expensive to buy the part but just tighten the screw intot eh predefined place.

I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.

  • Customer: Karen from Oklahoma City, OK
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

My drip bowls were scorched and discolored and difficult to clean

  • Customer: Claudia from Milwaukee, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Broken rear stove drawer glide

  • Customer: John from Maysville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

It was a rather simple fix--just replacing burner pans

  • Customer: Vicki from Jefferson, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

reflecter/drip pans wrong size

  • Customer: Dann from Glendale, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.

Eroding burner drip bowls

  • Customer: Edward from Hamilton, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement

burnt out drip pans

  • Customer: Barbara from KAMUELA, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

Replace burner drip pan

  • Customer: Ray from Council Bluffrs, IA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.

Bad Receptacle

  • Customer: TROY from YPSILANTI, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 6 people found this instruction helpful
I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!

door glide broken

  • Customer: David from Port Orange, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
removed the old ones.then installed the new ones.

the drip bowls had rusted through

  • Customer: DANIEL from sanborn, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.
All Instructions for the FEP310KW4
46-60 of 161