Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FEFL68GMA > Instructions

FEFL68GMA Frigidaire Range - Instructions

All installation instructions for FEFL68GMA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEFL68GMA
46-60 of 729
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broil element was bad.

  • Customer: William from Fort Myers, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 7 people found this instruction helpful
It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

The smaller element of a dual element stove would not heat up.

  • Customer: Debra from DISPUTANTA, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Unplug the unit or turn off power at the electrical panel!!!! I removed the 2 screws that hold the top surface of the stove down. On my range, these are located in the front, under the the top surface. You have to open the oven door to remove them. I propped the top up with a couple of 10 inch pieces of 1 x 2 then removed the screws on each end of the bracket that holds the elements in place. I used a 1/4 inch nut driver for these. With needle nose pliers, I removed the 3 retaining clips from the bracket and removed them from the element with a screwdriver and transferred them to the new heating element. The holes around the outside of the element are numbered so it's easy to know where they go. Laying the new element next to the old one, I moved each paddle-type electrical connection one at a time to the corresponding place on the new one. Put the retaining clips back in the slots. Screw the mounting bracket back in. Put the top down and secure it with screws. Very easy repair.

Replace cracked glass in main top

  • Customer: Cynthia from Plymouth, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
First I pulled the unit away from the wall and unplugged it. There are a few screws that hold the top in place - access them from the top/front/underside of the main top - pull open the oven door to get to them. Once these were out, I gently slid the main top forward. There are tabs in the back that fit in slots just under the control panel - just work them free as you slide. I slid the top forward enough to get past a narrow aluminum plate/tab (part #26B) in the very front that runs the width of the top. Once it's free of the tabs in the back, and the front is free, there is enough play in the wires & elements to move the top to one side of the stove and access the heating elements underneath. The heating elements are attached to brackets; the brackets (part# 26) are attached to the main top. You can leave the elements & wires attached to the brackets - there is one screw per bracket that attaches it to the main top - just remove the bracket screws. It requires either a square screw driver or a 1/4 inch socket. Do one side, then the other NOTE WHICH HOLE THE SCREW GOES IN, as there are a few to choose from. After the brackets were free, the top comes off. I moved the back tabs (part #18) from the old top to the new - NOTE THE ORIENTATION OF THE TABS. I didn't, and had to flip them over, after 20 frustrating minutes. With the new tabs in, I replaced the heating element brackets, then slid the main top back to its original position. If the tabs are in the right position (see above) it'll slide right into place. I had to work the narrow metal plate in the front under the main top with my fingers when sliding it back on. I replaced the front screws underneath, plugged it back in, pushed into place, and it's working fine. About 40 minutes total, extra if you don't note the orientation of the tabs in back, or the location of the element bracket screws. The oversized heating element won't let you put it in incorrectly.

the indicator light for burners broke and shorted agaist the back panel on range

  • Customer: James from Caldwell, ID
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 12 people found this instruction helpful
This caused the burner switch cotacts to arc burning out the switches. It took 30 or 43 minutes to replace the switches and put the range back together. The bake element took 10 min. ti replace. Grandma has her range back and I am a happy grandpa!! Thanks for the help and we saved over $170.00 for the repairs. Jim Johnson

Range would start beeping and needed to be unplugged.

  • Customer: George from TURNERSVILLE, NJ
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.

switch had a diffirent lug configuration

  • Customer: Robert from Andrews, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 16 people found this instruction helpful
made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

no display on display module

  • Customer: robert from orange, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 15 of 37 people found this instruction helpful
check for power in to the module,when it had incoming power,order new module,jnstalled it and walah done.

Oven light stayed on & smelled like electrical burning.

  • Customer: Vincent from Brunswick, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 25 people found this instruction helpful
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Electric burner switch shorted out.

  • Customer: Armando G from Alice, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

broken lens over oven light

  • Customer: Leslie from Warsaw, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 20 people found this instruction helpful
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

switch not always turn off

  • Customer: Jerrold from San Marcos, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

oven baking element burnt into

  • Customer: Teresa from Marengo, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 4 of 5 people found this instruction helpful
my husband did the repair.He unplugged the stove removed the element and installed the new element.plugged the stove in and checked operation of element.Stove works great

N/A

  • Customer: Dineshbhai from Rincon HWY21, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Bake element began burning itself up.

  • Customer: Don L from La Grande, OR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.

L.F. large burner element either on full hot or off. Would not cycle in and out with element control switch setting.

  • Customer: Gerald from MADISON HTS, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it started but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.
All Instructions for the FEFL68GMA
46-60 of 729