FEF336ECG Frigidaire Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gasket In Door Replaced
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Parts Used:
-
James from Greenville, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat.
Turned the main power off to my oven. Got my part removed two screws took the old bake element out put the new one in, replaced screws, turned power back on and boom it was fixed. Thanks so much for making it so easy.
Parts Used:
-
Nanci M from Greenwood, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Element burned out in 15 months
Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.
Parts Used:
-
James from Basking Ridge, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner not working
Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.
Parts Used:
-
timothy from Kingsland, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
55 yr old wall oven had burnt out seal
Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket
Parts Used:
-
Diane from Natrona Heights, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Element burned out
Removed two screwa holding element in place. Removed the connecting wires. Attached wires to new element. Reset emlement, replaced the screwa and I was done. Actuallt, I did as exactly as indicated in your film discribing the installation. P.S.-Part arrived in two days inspite of the impending hurrican. Extremely satisfied.
Parts Used:
-
RICHARD from CORAM, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Broken oven door glass
I followed directions for replacement of the glass from the web. Replacement was simple and easy.
Parts Used:
-
Joseph from Cranberry township, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burnt-out bake element
My wife had seen a small fire in the bottom right of our oven, and I quickly turned off the oven unit, which put out the fire. We tested the oven a couple more times after it had cooled and determined that indeed the bake element had burned out. I'd used PartSelect before and been very pleased with their service (speed, ease of use of site, etc.,etc.) so I ordered a new bake element, which arrived in two days! It was easy to replace: I turned off the circuit breaker, slid the oven out from the wall, disconnected the plug, and then got to work undoing the tabs that hold the bake element to the rear wall. The only little glitch was that the screw heads on our range were neither slot nor Philips - they turned out to be small square-socket screws. I couldn't see that until I turned a bright flashlight on the job. Then it was a simple matter of trading out the screwdriver bit, disconnecting the old element, plugging in and attaching the new one, and away we went. Oven as good as new! Thanks, PartSelect!
Parts Used:
-
Henry from Stow, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
element broken in half
followed the video provided and installed it as instructed. Video and instructions provieded were very helpful
Parts Used:
-
James from Dallas, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Heating Element broke
Remove bolt from both ends of element carefully as not to damage wires connected to the ends. Replaced with new element. Simple.
Parts Used:
-
Jennifer from Columbia, MD
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
rear drawer glide/problem was when wife saw video
It took about 3 years to order and 3 minutes to fix. forgot to turn off "easy" video on conputor. Wife watched was mad........... for taking so long to fix. 41 years married, any video to fix wife and get me to 42 years as easy as changing draw glides? Thanks Jon
Parts Used:
-
Jonathan from East Millinocket, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burner switches had only two settings off and high
After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!
Parts Used:
-
Margarita from Palmyra, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
One terminal was hard to remove.
Turned off electric at breaker box for range. Using a socket wrench from my little pink tool kit, I removed the two screws holding the unit at the back of the oven. Gently pulled each side of the unit out, exposing the terminals. Holding with one hand and wiggling the terminal with the other, removed the element. One was very easy, but the other was harder. Next I connected the new element to the terminals. Gently pushed the terminal back into the oven wall and replace the screws. Last turned the electric back on and then turned the oven on. The video that was online was very helpful.
Parts Used:
-
Alma from Lonoke, AR
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Front and rear glides broke on bottom drawer.
After watching the videos on removing and replacing the front and rear glides on the bottom drawer, I was able to take the bottom drawer out, use a screwdriver to pry all the glides out of their slots and snap them all back in place in less than a minute. Without the videos I was completely helpless in knowing the sequences to performing this task.
Parts Used:
-
charles from orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bottom Element required replacing
Thanks to the video on your web site, the replacement was very easy! We had a hard time removing the screws from inside the oven as we did not have a hexnut driver, but once we removed the screws then we lost one of the wires, (it fell back into the little hole) and then we had to remove the back of the oven to get the lost wire, push it through the little hole and we connected the new element, screwed it back in and then we baked some cookies.
Parts Used:
-
thomas from holtsville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!