FEB30S5DCB Frigidaire Wall Oven - Instructions

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elements, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

I ordered the part based on the parts list provided. The part arrived by mail 2 days after I submitted my order by email. True to the word in their website, they mailed the item the same day I placed the order.

It took approximately 20 minutes to remove the damaged hinge and replace the new one. No problems at all and I was extremely pleased with the rapid arrival of my order. I had studied the door and the hinge placement in advance and knew exactly what was needed. The only tool I used was a screwdriver. I removed the plate on the side of the door...lifted out the damaged hinge...replaced it with the new hinge...replaced the plate covering the hinge parts and replaced the door on the oven. An easy fix....

step one. removed 2 screws from back panel
step two. gently pulled out element
step three. took new element out of box
step four. began hooking new baking element
step five. electrocute husband (forgot to shut off electricity)Oh, by the way he survived!
step six. turned off electricity to oven
Step seven. hooked new baking element to oven
Step eight. replaced two screws to back panel
All went well with the exception of step 5 and it bakes great!

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

I removed the door with instructions from the owners manual, printed out the door parts diagram from your web site to determine how to take door apart to replace old hinges with the new ones, what took long was cleaning the door glass surfaces while I had the door apart being carful not to break the glass, do not use a green pad to clean the dirty film from cooking on the glass surfaces I did and it left scratches on the glass. I used alot of common sense and reversed the takeing the door apart process to put is back together.

Removed two screws holding broiler element. Released two spring hangers on near the front of the element. Pulled element away from oven and pulled two wire connectors off. Simply reverse process to install new one. Wasn't the problem.

Removed electrical connector and two screws. Attached the electrical connector to the new probe and attached with the two screws.

On a beautiful Saturday morning, we began the oven repair by argueing about who should hold the door, and who should use the screwdriver, we managed to remove the oven door by unscrewing 8 screws (2 top, 2 each side, 2 bottom). The bottoms were the most difficult as the incredible hulk must have done the original assembly. The door was heavy & awkward and the new hinges have a little lock that must be unlocked in order to hook it inside the frame. Of course the screwdrivers we had all had long handles, so after some shouting about where all the shorter handled ones were, I found a stubbie at which my husband gave me a dirty look. After more grunting & shouting we got the door back on.

Twisted replacement bulb into place easily. Let there be light!

I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.