Parts That Fix Frigidaire Washer FAFW3801LW3 Leaking
Leaking is a commonly reported symptom for the FAFW3801LW3 Frigidaire Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FAFW3801LW3 Frigidaire Washer that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
The water inlet and dispenser valve is used in washing machines. The function of this part is to control and monitor the amount of water flow into the washer. If there is leaking during use, your machine will not fill with water, or there is no hot or cold water entering the washer, it is important to replace the water valve to solve the problem. For this repair, you will need a Phillips head screwdriver and a flathead screwdriver. For installation instructions, refer to the manual provided by the manufacturer. Remember to unplug your appliance from the power source before beginning this repair.
Customer Repair Stories
Frozen pipe
-
Frank from Auburn, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Valve dispener would spray water all over inside of washer.
-
Julie from Lancaster, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle. NOTE: This part has been redesigned by the manufacturer and is interchangeable with the old design.
Replacing your Frigidaire Washer Bellow Kit
Customer Repair Stories
Moldy smelly rubber cowl around door.
-
Emil from BOULDER, CO
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
Old Bellow Ripped
-
Peggy from New Castle, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Also known as tub-to-pump drain hose.
Replacing your Frigidaire Washer Drain Hose
Customer Repair Stories
The drain house was penetrated by a piece of metal from coin catcher
-
Kimberly from East Moriches, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
Replacing your Frigidaire Washer Spring-Held Bellow Clamp
The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not start or spin, you may need to replace the door strike. This part is for front load washers and is white in color. The part is made of plastic and is roughly 2 inches in length. To complete this repair, you will only need a Phillips screwdriver. Most of our customers found this repair to be easy and took less than 15 minutes to complete it. This part is sold individually, not as a part of a kit, and is a genuine part approved by the original manufacturer.
Replacing your Frigidaire Washer Door Strike
Customer Repair Stories
washing machine front loader door would not close, making the machine useless
After looking all over for the part,and no ... Read more t finding it I was thrilled when you carried the part. Even though the machine is old, it works great. Thank you for the selection of all the parts you carry and how you make it so easy for us to find what we need. , and having it in stock, which was mailed right away, so I could replace the catch and have the washer back in use in less than a week. Thank you
-
Susan from Vero Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Broken Door Catch
-
Joy from Columbia, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
Replacing your Frigidaire Washer Drain Pump - 120V 60 Hz.
Customer Repair Stories
After a full cycle the washer would not drain the water
-
sara from North Miami, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
would't spin all water out or rinse out clothes
-
kenneth from willard, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Replacing your Frigidaire Washer Dispenser to Tub Hose
This is a door hinge with bushings and works in conjunction with your washer. The purpose of this part is to attach to the outside of the front door panel to help with the lid opening and closing properly. The hinge will fasten the front panel of the washing cabinet to the lid of the washer. This piece is roughly 9 inches long, almost 3 inches high, and roughly 2.5 inches wide. The reason for needing to replace this part is if your lid/door will not open or close properly, which may lead to leaking.
Customer Repair Stories
Door hinge bottom bushing broke - Door latch no longer lined up with catch
Once hinge screws were removed I put a towel down on a counter to keep the front of the door from getting ... Read more marked up and proceeded to remove all of the screws around the back of the door so that I could lift the frame up enough to remove the broken hinge and insert the new hinge. It was a bit tricky to get the new hinge with bushings in place. I gently lifted the frame up with a flat head screw driver to widen the opening so I could get the bushings on the new hinge into position on the frame. Make sure they are properly inserted before you start tightening up screws.
Next, replaced all the screws on the frame, returned to the washing machine with helper who held the door up while I aligned the holes in the new hinge to the holes in the frame around the opening to the washer.
After everything was secured and tightened, to my surprise, the door latch did NOT line up with catch without lifting up about a 1/4" or a little more, on the bottom of the door. If someone slams the door without doing that you could break off part of the plastic latch or damage the catch inside the door frame.
I believe the original holes on the door frame were not drilled precisely during the manufacturing process and that is why the bottom bushing broke. We have always had to lift up a bit on the door to line up the latch with the catch. Eventually the strain on the bottom bushing caused it to break and then the door tilted down so you had to lift it up about 3/4 inch to latch it. I bought new hinge because if the top bushing broke the door could have come off.
Next time I buy a washing machine, I will pay more attention to the line up of the door latch with the door catch.
Flashlight helped me line up the holes.
-
John from Dover, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Bushings in door were worn out so door real sloppy- had to raise it up shut it
-
RALPH from GREENFIELD, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This part is located between the front and rear outer tubs.
This is not the complete door.
Replacing your Frigidaire Washer Outer Door Panel - White
Customer Repair Stories
Door sagging, plastic broken
-
Paul from BOTHELL, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Door was sagging so strike would not line up upon closing the door.
-
Paul from BOZEMAN, MT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.
Replacing your Frigidaire Washer Front Load Washer Door Lock and Switch Assembly
Customer Repair Stories
Washer would not spin
-
Keith from Sayville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Door on washer wouldn't lock or start
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
-
DOUG from KING FERRY, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Replacing your Frigidaire Washer Door Glass
Customer Repair Stories
Glass broken
-
Lillian from PHILADELPHIA, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Glass inner door cracked due to machine rocking
-
Gennaro from Nutley, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers