F9157W0 Roper Range - Instructions

Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

Isimply pulled the old burner unit and followed the instructions that came with the replacement.

Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.

Sensor matched perfect, but had to pull large upper rear panel to find location. From there took a few minutes to reassemble back. Did not un hook gas but turned it off. Obviously unplugged power. Oven works fine.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.

The Temperature Sensor was actually installed from the back of the oven. I had to remove about six(6) screws to remove a metal panel on the back of the stove. The connector the Temp sensor came with did not match the existing connector however it did come with wire nuts as an alternative. I cut the wires and connected them with the wire nuts and replaced the pannel. Very easy fix and my 13 year old oven still runs like new.

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

Followed Mfgs instructions.

Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.