F7908W0 Roper Range - Instructions

ordered new broiler pan

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.

The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn

just pulled and removed the old burner then pushed the two new power connections into same place - no tools - works perfectly

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new bracket and installed the burner. double checked everything and lowered the top. Done

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.

Had to screw off old terminal block & screw on new one

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

took it out of the packing material, wiped it off and plugged it into the cooktop. Works like a champ, needed no tools. My order was processed and sent out promptly, and arrived quickly. Thank you very much.

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML