Quick Question!

Have you ever purchased from PartSelect.com before?

Models > EWMGD70JRR0 > Parts

EWMGD70JRR0 Electrolux Dryer - Parts

All parts for the Electrolux Dryer EWMGD70JRR0

Below is a list of all parts for the Electrolux Dryer EWMGD70JRR0. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the EWMGD70JRR0
1-14 of 131
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.16

'M' Series Ignition Coil Kit

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes...

$45.65

Lint Filter

Located at the front of the washing machine, this dryer lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 14 inches long x 11 inches high. It has a plastic frame and a mesh body to catch debris. If your filter needs cleaning, the dryer cycle will take longer due to a buildup or lint or fabric softener affecting the air flow through the filter. If there is a buildup, try scrubbing the filter with hot water and soap. But if the filter is damaged, worn, or torn, it should be replaced. Cleaning the lint filter before starting the drying cycle is a great way to ensure your dryer performs properly.

$22.09

Flame Sensor

This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer i...

$9.91

Adjustable Leveling Foot - Black

This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.

$6.65

SCREW

$31.04

High Temperature Adhesive

This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before applying the adhesive, ensure that the area is completely clean from any debris and is dry. You may wish to use small clamps to hold the material in place while it dries. If the felt has come loose or broken apart, this may cause your dryer to make loud noise, indicating that new felt or rubber needs to be glued into place. Use gloves to apply glue.

$6.86

SCREW

Sold individually.

$16.62

LIMITER

$40.71

SENSOR-MOISTURE

$15.44

LIMITER

$4.74

SCREW - M5 X 0.8 X

$48.52

LATCH

This door latch is used in dryers to help keep the door closed during a cycle and releases the door to open when the latch is pushed. If the door does not stay shut, it can affect the cycle and your clothes will not dry effectively. In this case, replacing the latch can secure your door and solve the problem. The tools needed for this repair are: #2 square bit, Phillips head screwdriver, and a flat head screwdriver. Remember to wear safety gloves before beginning this installation project. Refer to the manual provided by the manufacturer for installation instructions.

$32.31

ROLLER

This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotat...

$20.41

THERMOSTAT

All Parts for the EWMGD70JRR0
1-14 of 131