EMO3000HCC05 General Electric Microwave - Instructions

took of cover removed switch and replaced with new one

Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

1. Turned off circuit breaker for microwave.
2. Removed screws holding the bottom cover of the microwave; cover is hinged at the back, so it dropped open and stayed out of the way.
3. Unplugged turntable motor and removed screws that hold turntable motor in place.
4. Pushed broken pieces of the plastic turntable coupler out of the way (hole for motor's axle not big enough to remove them).
5. Put turntable coupler into hole in bottom of microwave interior, held it in place while putting the motor axle into it from below.
6. Replaced screws holding turntable motor in place, plugged in motor's electrical connector.
7. Closed bottom cover and replaced screws that hold it in place.
8. Switched on microwave circuit breaker.

first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.

Ordered and replaced turntable coupler. Still didn't work.
Ordered turntable motor. Left bottom of microwave open for motor to arrive since the parts are shipped so quickly. Sure nuff parts arrived 3 days later, replaced and walla walla fixed in 10 minutes. Simple, simple.

Lower base of the microwave, about 6 screws,
replaced broken light bulb socket,then re-installed.
Installed new light bulb.

I open the door to access the back panel. I used a screwdriver(flat) to unsnap the inside door frame cover. Next, the removal of 2 philips screws near the door spring locks to allow the front frame removal. Unsnap the front frame from the door and remove. Next, remove 2 philips screws and remove the handle. Install the handle to the new frame and in reverse order, reinstall the new outer frame. Simple.

After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.

Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.

First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.