EMO3000CWW03 General Electric Microwave - Instructions

I was told by 2 different appliance technicians that the crumbled/melted light socket could not be replaced which meant replacing the entire microwave (expensive!). Other posters on your sight described the repair steps and I gave it a try. The hardest part was probably figuring out which switch in the fuse box belonged to it (now marked clearly). It was a simple matter of unscrewing the bottom panel of the microwave to access the socket, pulling the crumbled/melted unit off and shoving the new one on. I can't believe the repairmen didn't want any part of even giving it a try.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

The repair was simple. It was just a matter of removing the upper vent grill to access the screws for the panel frame. Then I just popped out the old frame and installed the new..and the micowave is as great as it was new. The PartSelect website allowed me to see a visual map of all the parts of my microwave which allowed me to find and choose the right piece for the job. It only took 5 minutes for the repair.

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

First remove the inner frame, take out the two screws holding the handle on. Detach the handle and outer frame making sure you hold the glass as this comes out with the frame. Fit the glass into the new frame, fit the frame to the door, sit the new handle in position and screw the two screws through the door skin and outer frame.Clip the inner frame in position and job done. It's as easy as that.

Removed the 1 inch plastic frame on inside of door, gave me access to 1 set of screws. The problem I encountered was, getting to the set that holds the handle to the door.I didn't realize the metal frame held the outside with flexible hooks, therefore once u snapped them off, the outside with the handle on it HIT the floor glass and all!
Fortunately it didn't break. Supporting the outside is most important.

took of cover removed switch and replaced with new one

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.

Lower base of the microwave, about 6 screws,
replaced broken light bulb socket,then re-installed.
Installed new light bulb.