EF48DBSS Dacor Refrigerator - Instructions

plastic warped in ,spaced out and, the socket snapped back in place.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.

After receiving the replacement emitter and receiver boards from PartSelect.com, I following the troubleshooting paperwork that came with my order to ensure the parts I ordered where the problem. After which, it was very straight forward: unplug the frig, unscrew the 3 screws on the covers for each board, unplug the push-pin connection, remove the board screw, set the new board in, and plug back into the connection. It took approximately 20min.

I unplugged the refrigerator
Opened the freezer door
Opened the ice maker door so that I could easily get to the emitter and receiver
I used a phillips head screw driver to remove 3 screws from the emitter plate and 3 screws from the receiver plate
I unplugged the faulty circuit boards--this took some tugging
I firmly plugged in the new circuit boards and replaced the screws
I waited about 30 minutes and the ice maker began making ice again

I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)

Unscrew the three phillips screws holding the flipper and electric eye unit, pull it out a bit to unplug the connector. Take the assembly over to a flat surface, and use pliers and or crew driver to pry/pull off the press-on retainer on the hinge pin. Pull out hinge pin, remove the broken flipper. Put new flipper in place making sure spring is behind the flipper (holding it open). Reinsert hinge pin, and then reuse the press-on retainer to hold in in place. Then take the repaired assembly back to the freezer, re-plug the plug, and then reinstall the unit using the 3 phillips screws. Easy Peasy.

Light was blinking on the Electronic Control Boards. Ordered replacement (emitter and receiver)and installed, and now it's working.
Some note: 1 year ago, the board started to blinks (meaning it's bad) but it was still making ice. This gave me a false error when it really failed, took the risk and ordered the replacement parts and all is well now.

One more thing to pay attention to , and it may only be on my model of refrigerator, but the wires harness that connect to the receiver board (big board) have large and stiff wire. With limited space where the board and the wire are seat at, it put lots of pressure on the pressure on the board's connector. This pressure, over time, will cause the right angle connector's solders to crack and may be a contributor to the failure. If you're installing the new board, try to re-inforce the connector with some rubber heat glue and also relieve pressure from the connector's end, which I hope will prolong your board.

worked great parts were perfect!

Pry open the front dispenser outer cover. Remove a screw holding ice door dispenser unit, remove old door chute, remove and place coil kind of stuff (connecting to panel) old chute to new one and reinstall.

Repairing a refrigerator is inimidating to say the least. Our ice maker has broke twice in the two years that we have owned it. The first time we had a service repair faciliting come out and they replaced it for about $200. The second time I had no idea what the problem was until I came to this repair forum. I soon realized that the electronic control boards needed to be replaced. Received the part two days after ordering and it took all of about 5 minutes to unscrew the old boards, pop them out, and put in the new ones.

Love your website and the money that you saved me!!! Thanks a million!

hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.

power off, 3 phillips head screws on either side of freezer. unplg each board, plug new ones in completely. ( cannot mix them up, size difference) replace screws and enjoy ice cold beverages once again!!!!!!!!!

I wasn't sure what the problem was, but the ice maker seemed simple and on-line resources suggested the control and motor assemblty was at fault. I searched the internet and Partsource had great diagrams which I could match to the part in hand. The price was right (way less than the local stores) so I ordered it.
I unplugged the unit from the power in the freezer, but unplugging the entire refrigerator works too. I pried off the white cover on the front of the ice maker, which snaps in place top and bottom. There are three screws holding the contoller (the entire front piece), remove them, pull off the controller and push the new one in place. You may have to turn the blade shaft to line up the notch on the shaft to the motor. Then reinstall the three screws, The screws go into plastic so it is easy to cross thread them, so be careful, I actually think I did with no ill effects. Snap on the cover and repower the unit. Done. Simple and quick.

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed