E23CS78HPS0 Electrolux Refrigerator - Instructions

The diagram for the shelves is wrong I did not receive the right part. I ordered the crisper glass insert and received the vegetable drawer glass.

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

followed the video instructions and wa-la! Saved my money by not calling the repair man, the shipment of my part was fast, and the repair was even faster. Thank you for helping me in my repairs. Very Satisfied!!! Carol

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

husband did it took only a few min part was easy to find

Unscrewed the top hinge, lifted door and laid it down. Took off old hinge bearing and snapped new one in. Put door back and no more noise. Easy fix. Only problem was that I couldn't believe I waited so long to fix that simple problem.

Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

take of the tray & take parts out & installed the new ones

Repair as illustrated was right on. Repair was easy. No problem except still no water for ice or drinking. The valve was not the problem. Filter was replaced prior to valve replacement. Must be a electric switch some where. 3 Yrs ago I have replaced the water activation plastic lever for drinking which was a bit difficult and it turned out ok.

Installed new support. I placed the new one in the hole provided and taped in the locking peg with a small hammer. The total installation took about three minutes thanks to the excellent video provided on the web site. Thanks

The water flow on or refrigerator was just trickling out. After trying to make sure there was no kink in hose, I called for replacement. Water flows great now... actually better than when new.

I was worried that the support was a permanent fixture in the refrigerator wall. But I pried it out and replaced it with the new part. Holes were exactly the same size so the new part easily replaced the old one.

Purchase was easy. Delivery was quick. Install videos was accurate. Made it eady to as DI project. Safe place for purchase and support. Saved on cost of professional visit.

I followed previous directions, and would recommend them! Briefly, I removed the plastic covers for the water filter, water tubes, temperature control switches to allow removal using a screwdriver and a nutdriver(I think)to remove the hexagonal screws. I also removed the water filter before beginning. I pressed the blue thingies in the back towards the base to remove the water supply lines. It was a bit tricky, and took the bulk of the repair time, but they came lose once enough pressure was applied. I took out the old filter base, put in the new one, attached the water lines, and put back all the covers. Everything comes apart very easily, and went back together very easily. A simple repair that had us back in ice and filtered water within an hour!