E23CS75DSS5 Electrolux Refrigerator - Instructions

replaced them with the new ones

I tapped in the peg like it showed in video and pried out with flat screw driver and hammered other peg in flush with part

unplugged frig, removed shelves & inner lower back panel in freezer side, removed defrost thermostat from tube, cut the wires and spliced in new stat wires with provided wire splices crimped together and replaced thermostat on tube it has been a week and no ice so far??. this was after 2 trips by the repairman who replace the defrost timer board which was most likely good at a total of $160!!! still cheaper than $1000 for a new frig!!!!!!!!!!!!!!

Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.

replaced with kit, very easy unplug unsrew and replace, any one can do it

When my wife and kids moved down they lost the upper bracket and the screw for the lower cam. parts show up and matched perfectly to the orginal no issues at all

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

We watched u tube repairman then did exactly the same thing. Then we did a high five.

To describe this replacement as "really easy" is an understatement! The hardest part was digging the socket set out of the tool box. The instructions were well written, as were descriptions of fellow home do it yourself types. Those gave me the confidence to just for it. I am so tickled with myself and the money I saved! My hubby is pretty impressed too! Cathy

Watched a video on You Tube. They said it would be a six minute job, but it turned into about a 20 minute job. The refridgerator look a little different than the one in the video. Appliance had a computer tape that connected to the exterior and as we were putting everything back together we accidently pulled it lose. Worse part was trying to get that back together. Now it works perfectly.

followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.

Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

after I contacted Frigidaire and they told me that it was the vent fan and told me where it was, looked up the part and got a new one from Part Select. When it arrived I unplugged the old one and plugged in the new one and reattached the holding bracket. No tools required. I then turned on the dishwasher and it works perfectly. If you get an "ou" error message on your Frigidaire Dishwasher, the money you will save is great!!!!