DWCA500AAW Admiral Dishwasher - Instructions

Simply remove the washer nut,then pull the float assembly. As far the lever,just unscrew the screw and replace the actuator lever. What was great about everything I was able to go to the presented diagram. This allowed me to find the exact parts I needed. Of course make sure you have the model number.

Our dishwasher got to the point where it would not complete a wash cycle. I found that by jiggling the door latch, the dishwasher would whir back to life. For awhile, if I put a clothespin on the door latch, somehow enough pressure would be put on the switch to keep the dishwasher going. Finally, the dishwasher refused to cooperate...so I ordered a replacement switch.

The repair was easy. I only had to remove the interior door panel, unscrew the metal bar at the top of the door and underneath the door panel, then remove the black plastic shield. After that, it was just a matter of wiggling the old switch out and wiggling the new switch.

CAUTION: Be very sure that the power to the dishwasher is turned off. I got a scare because I thought the circuit breaker was off, but I had flipped the wrong one and suddenly, with my fingers very close to the bare connectors, the dishwasher came back to life briefly. I ran downstairs and found the correct circuit breaker and all was fine after that.

Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.

That's it !!!!!!!!!!!!!!!!

removed spray head, pulled motor/pump assembly. took apart impeller housing and then removed motor and pulled impeller off its shaft, the most difficult part was actually pulling off impeller from the splined shaft. I actually broke old impeller in the process. The good thing is that the new seal came assembled with new impeller so that was not a problem. After re-assembling everything it worked fine and still works for a week since repair.

Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.

Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed.
Super fast shipping on items!! Great service.

So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott

Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

The repair was EASY! Took bottom drawer out. Used tool to remove 3 screws that held belly screen and washer arms together. Used needlenose plyers to unscrew long pointed center screw (plastic!) then reassmenbled! Hey BATTA BING BATTA BOOM!

Dealer phone quote = $250. DIY repair = $55.
Turn-off DW electrical circuit breaker and shut-off hot water supply. Remove lower Front Access Panel and Toe Panel. Disconnect hot water supply, corrugated drain hose, electrical connection, and uncounter mounting brackets. Slide-out DW (being careful not to scratch flooring) and gently tip DW onto its back side. Rotate Ring-Lock at underside of Tub and (from inside the Tub) carefully lift out Motor-and-Pump assembly. At the Motor-and-Pump assembly, unscrew Center Spray Nozzle and remove Lower Spray Arm and lv Filter. At the end of the Impeller, remove Chopper Screw, Chopper, Chopper Plate (rotate 1/4 turn) and Chopper Wear Ring. Remove Motor Mount Screws and Motor Shield. Loosen Impeller {NOTE: left-hand thread} from motor shaft by the holding Motor Fan stationary and unscrewing Impeller. Pull apart the Motor and Impeller; discard old Impeller. Gently and thoroughly clean the internal surface of Housing Assembly seal with a toothbrush and soapy water. Carefully reassemble in the reverse order using the new Impeller. (Prophylactically, I also replaced the Motor "O" Ring and Pump Gasket.) DW works perfectly; no leaks!

Actual i missed diagnosed the leak and ordered a very expensive door gasket. The leak was coming from shrinage of the wax resevoire o rig and the tab seal for the soap dispensor. I missed the trees the forest got in the way. The leak was dripping alond the front panel well away from the main door seal.

I cleans a the plastic surfaces and noticed a lip around the opening for the reservoire and used 150 sandpaper to remove it. Replaced the O ring, tab seal and bothe selonoids and cleaned everything. Put it back together. Works find lasts along time

Remove inner door by removing 7 torx screws. flip inner door up, propping it between the open door and the countertop.

Leave the drying solution reservour in place, remove two screws holding wax motor retainer. remove motor. (You might want to dissassemble door latch mechanism and replace latch seal, which is probably why wax motor failed to begin with. it simply slides over the latch FROM THE INSIDE.) Then reassemble.

I also cleaned up the main inner door seal. after that, the dishwasher leaked pretty good everytime the sprayer arm revolved. It took awhile to figure out I had rubbed off some rubber, although not much, BUT ENOUGH to make it leak.

SIMPLE FIX: Simply pull out seal, TURN IT OVER, so the back is now the front, AND RE-INSERT. No more leak. Saved 42 dollars.

Also: if your washer has two wax motors, (and you don't use drying agent) just swap the drying agent wax motor with defective soap dispenser motor. No cost repair.

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

Took off the float, the jam nut was hard to get off, we ended up breaking the bottom piece of the float to get it off, but that was okay because we had a new float. The new float went on real easy and the jam nut went back on real easy. The foam insulation strip was real easy to get off we got a good hold of one end and striped it off slowly so there was nothing left on the door, then we cleaned the surface and put on the new insulation strip. We ran dishwasher to test it and there was no leak. Awesome. Cheap and easy to repair. We were impressed.

Once I pulled the old broken drain valve lever lifter off the shaft, the shaft rotated counter clockwise. I then had to turn shaft back clockwise so there was enough room to slip the new part on. Needle nose pliers worked great to hold it in place while regular pliers in the other hand was used to turn the shaft.

removed inner door panel. tested ythe Wax motor that operates the soap dispenser latch. It tested OK so I removed dispenser assembly. replaced the worn plastic parts and reinstalled the inner door panel.