Models > DU599 > Instructions

DU599 Jenn-Air Dishwasher - Instructions

All Instructions for the DU599
76 - 86 of 86
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Motor runs, no water sounds, poor cleaning
Disassembled spray arm the way the website describes. Found an amazing accumulation of scale and soap scum. Everything was seriously gunked up. Cleaning and rodding out the spray arms and pump housing screens takes a minute. Be careful not to break or puncture the screens. Dont try slapping the pump housing filter on the driveway. Its brittle and will break. Suggest buying a new one anyway. Its nearly impossible to clean. Simply clean it all up and re-assemble. Oh and bask in the praise from your wife.
Parts Used:
Pump Housing Filter
  • Harlan from Santa Maria, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would pump the used water out.
Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.
Parts Used:
Float Switch
  • Robert from Bandon, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
leaking water
replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.
Parts Used:
Door Gasket - gray
  • Noel from Temperance, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Nipple that upper spray arm goes on.
Maytag dealer said the part was unavailable but there I sat looking at it.
Parts Used:
Upper Spray Arm Outlet - White
  • Roger from Saganaw, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
water leak - tub overflow
remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.
Parts Used:
Float Switch
  • walter from salisbury, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
stretched door springs
Locked door closed, removed lower access panels with 5/16" nut driver, removed old springs with needle nose pliers, put plastic piece on top curved end of spring and placed on slot in door bracket as shown on instructions with part. Did same thing for the other door spring, used the screw driver to stretch the springs down to the first hole in on the base of the dishwasher on each side. Replace the panels. Job done!
Parts Used:
Door Spring Kit
  • Robert B from Frederick, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Not cleaning properly due to clogged parts.
I disassembled parts from the lower Spray arm to the Rinse Arm. Everything was gunked up, nothing was broken. I replaced the Lower Spray Arm, Secondary Filter, Pump Housing Filter and the Rinse Arm. I re-used The Radiant Shields, Filter Plate, Lower Spray Arm Seals and the O-Ring. Much of my time was spent cleaning before re-assembly. Assembly was no problem. I ran the machine afterward with no problems and very good cleaning results. I ran the videos once before starting. They were very helpful, as were some other people's experiences.
Parts Used:
Pump Housing Filter
  • Maurice from Wappingers Falls, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The door spring broke in half on the front door of a twenty two year old Maytag dishwasher
Easy repair, I put small marks under the counter to make sure the dishwasher went back in the same spot for easy screwing back in
Parts Used:
Door Spring Kit Door Spring Kit
  • Robert from Leominster, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door spring broken
once i got it out the spring was a breeze
Parts Used:
Door Spring Kit
  • Richard from Silver Spring, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
water leaking at door of dishwasher
based on instructions from previous customers, took off front control and door panel, removed old gasket, replaced new gasket by aligning tabs and pulling through with needle nose pliers, leaking stopped
Parts Used:
Door Gasket - gray
  • JOHN from SLIDELL, LA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Mice living behind the dishwasher
Mice were living behind and on top of the dishwasher and destroyed the pad. Had to throw it away. Ordering you was easy, and the pad fit perfectly.
Parts Used:
Insulation Pad
  • julie from golden, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DU599
76 - 86 of 86
Back to Top