DU486 Jenn-Air Dishwasher - Instructions

Removed lower spray arm and installed new seal under spray arm.Did not fix problem,I am guessing a low spray pressure.Everything checks out O.K.Anyone have some suggestions.How does the rinse aid get out of the holding tankr?

Removed front panel by removing four screws. Used 5/16 nut driver to remove six screws holding dispenser and disconnected two wires. Inserted new dispenser and reattached cover. Longest time taken was to realign cover properly. Best approach seemed to install with door as near vertical as possible and to start screws by hand. ONLY FOUR screws hold the panel in place. Very easy repair for anyone. part arrived sooner than expected.

I removed four philips screws to remove the front door panel. Next I removed the screws holding in the detergent cup. Removed the two electrical wires from the cup release. Reveresed the process to install the new detergent cup.

had to remove the iner door plate and remove the main switch or latch to get to the micro switches witch one had over heated over time,it is working like new at this time.

Changed springs on both sides as long as I was at it. Did this without having to pull out built in washer. Lock the door closed to give the least tension on the springs. Remove kick plate at bottom of washer. Remove small access panels on each side. If you have small enough paws you can reach thru the access holes and strectch the spring with your fingers to remove and install new springs or use needle nose pliers if you have to. Don't forget the nylon bushings that come with the springs or the metal on metal contact will eventually nick the springs hook and make them break . Hook top end of spring first (rounded hook) and then stretch spring by grasping between thumb and index finger and hook into bottom hole. Hardest part is having to lay on your stomach to do it. Reassemble and count the money you've saved.

removed retaining nut and replaced

Remove lower cover plate below door. Remove broken spring with needle nose pliers. Place plastic insert into upper spring loop and loop into hole on right spring hinge. Grab lower spring loop with needle nose pliers and insert through hole in lower frame base. Reinstall lower cover plate.

Removed the seal and replaced with new one. Job went very easy. Stop the leake. Thank you.

Claude Miller

Replaced whole assembly

Firstly, I'm a 58 year old female and this repair was relatively easy for me, thanks to all the marvelous instructions on this site from others who made this same repair. Like the others, I removed the four lower screws on the INSIDE of the door along either outer edge. Before that, in error, I removed the four screws along the very bottom of the door, big mistake, hard to get them back in correctly. Removed the door panel and took out the 6 nuts from the dispenser cup, slipped the electrical clip thingys from the posts by slightly wiggling them straigt off, remember which color goes where. Cleaned the area around the old gasket and reattached the new gasket and dispenser cup. This was a little tricky holding it in place from the inside while using the nut drive on the outside. Whew! That was the hardest part for me. Thanks to all for the previous detailed instructions. I now have really clean dishes! Yay! Great feeling of accomplishment.

This dishwasher is over 20 years old and still works well. The door springs broke and the skematic shows 2 springs on each side. The spring kit only includes one spring for each side which is the primary spring. Removed the bottom access panel, shut off the water line and removed the water line. Removed the top screws which lock the dishwasher in the cabinet and pulled forward about 6 inches to fully expose the springs. Replaced the two big springs, one on each side and adjusted for maximum pull of door. The second small springs were not necessary. Pushed unit back into the cabinet, connected the water line and tested for water leaks. Cleaned and replaced access panel and the door is light as a feather.

I removed the access panel and it was right there. one screw - disconect the wires & it was out. then right back in - access panel on, and done.

I removed the 4 lower Phillips head screws on the lower inside of the door.(thanks to a tip from Robert) This removed the front panel allowing access to the detergent cup. I removed the 6 screws holding the detergent cup. Removed the old detergent cup and gasket. Installed the new cup and gasket and reinstalled the front panel. Amazingly easy. Now it's on to my stove. I'm hooked on your website

Removed everything to get to the impeller, installed new impeller and put everything back together.

removed the bottom rack and the lower spray arm. With a star point screw driver removed 6 screws to take off pump housing. Lifted out the old filter. carefully bent the new filter (shipped flat) into a circle and connected end clips. Replaced bottom edge of filter into groove. Replaced pump housing and spray arm. Back in business!