DP400PD1 Uni Dishwasher - Instructions

I removed the whole spray assembly and replaced the base by removing the spray arm and re-attaching to the new wash arm support and diffuser assembly. When re-installed into the dishwasher, it works like new!

Just snapped the wheels on and attached the bracket to the existing part.

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

I removed all of the clips, that held the rubber seal inside the basket. I then replaced the new rubber seal with new clips. Very easy. The instructions were very helpful.

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!

This could not have gone easier! As long as you get the proper parts it's a piece of cake. I wish everything was this easy!

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

Laid over portable dishwasher and looked for evidence of a leak.Nothing obvious. Looked up Illustrated parts breakdown to see what could be the possible source and settled on the main seal on the water pump between the washing machine itself and the motor. Also replaced grommets on the heating element.She hasn't used it yet but am confident problem is solved.

Used a deep 13 mm socket to remove the old nuts, one of which was split which is what caused the problem. I installed the new grommets with the aid of a little olive oil and then I had to wiggle the element very slightly (more olive oil on the heating element where it slips in the grommet) while pressing down on the element. It slipped into place and then I reinstalled the new nuts and the wires and it was done. One word of caution the stainless mounts that hold the heating element are very sharp on the edges. If you use gloves and move them very easy to prevent damage to the mounts it will be easy to replace the grommets and the nuts.

Got the parts in a DAY! Wheels were broken and worn causing top tray to slip off runners- new wheels were easy to put in-used the screwsfrom the old ones and banged out the job in about 20 minutes, including letting my son help. Thanks Partselect, you've hooked a new DIY'er (my son)

There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.

I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!