DLL2880BAC Hotpoint Dryer - Instructions

Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.

Took off the top cover then took off the front panel and installed the new coils on gas valve.

the switch was stuck couldn't get the switch to pop out to stop the dryer when opening the door light inside also wouldnt go on. it only took a few min to take it the switch and replace the new switch the light now works also stops when opening the door it made my day easierhow easy it was to fix it. only take to use a pliers and screw driver.

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

Unplug dryer and turn off gas to appliance. Remove small vent door front of dryer for access to burner assembly. Reach inside and remove all three wires attached to the valve. Using a backup wrench remove the union that attaches the 3/8" gas line to the burner assembly. Remove the two bracket screws holding the assembly. The entire burner assembly can now be pulled out. Replace the faulty igniter by spreading the retainer clip and inserting the new part. Use extreme care not to touch the new igniter with bare skin...best to use a helper to assist holding the assembly while you insert the igniter. Then replace everything as you found it . Soap all gas fittings, plug it in and enjoy your dryer.

I was disappointed that there were No Instructions included with the part. So I found a you-tube video that wlked me through it...Took off back of dryer, then the top, then the front to get to the igniter...could not pull out the part, so I had to reach in and replace it while it was in the dryer. It Works!

Make sure your power is off, When loosened the top and tilted back, the first thing I saw was the door switch, I guess I was just lucky I disconnected the two wires and checked it and it was bad. Got my new one from you and installed it. It has a ground terminal, which my model switch only had the two terminals. It working fine.I took the bad switch apart and the one leg on the copper U shaped contact had broken off. The Belt I have as a spare.

PartSelect already has a good video explaining how to replace the bearing. The only thing that I would have liked information on is whether or not to add grease. It did not appear, on any of the PartSelect videos, that any grease was added. I read where some people recommended lithium or other types of high temperature grease. I knew better than to use automotive/petroleum based grease. I elected to use a small amount of lithium grease. Addressing whether or not to use grease would be a nice addition to your video.

The info from your web site was helpful. I had never taken a dryer apart and the instructions made the job easy. Used socket set to remove the back panel and top control panel. Then used a phillip's screwdriver to remove the two screws that hold the top of the dryer; these screws are accessed by opening the door to the dryer. To remove the front of the dryer remove to the two screws that are located at the top upper corners where front panel meet the side panel. Once these two screws are removed, remove the belt from around the drum and lift the drum out. The drum bearing is located on the back of the drum; remove the remnants of the old bearing and replace it with the new one. Retrace your steps to put the dryer back together. To get the belt back on track you will have to remove the lower back panel to access the belt drive and tension pulley. It is not difficult. God bless you.

inserted the latch into the opening in the front face of the dryer

Researching on the web I thought the trouble might be lint buildup or trouble w/ one of the parts involved in spinning the drum. However I cleaned out all the lint and replaced the belt and idler pulley and this didn't improve the smell (drum bearing was fine). I then concluded the trouble was the motor. Running the motor w/o the drum in place confirmed this was where the noise/smell was coming from. Replacing the motor was fiddly--I had to remove the clip holding the motor (pried the top w/ a screwdriver), wires (made a diagram so as to put back in same order, they were hard to get off--a pliers did the job), clamps holding the motor on the duct, the motor mount, the duct, the fan. Putting all this back together took a while (not hard just fiddly). Tested the motor w/out the drum in place and it sounded fine. Put the drum and back/front/top panels back and the dryer runs fine now. All parts came quickly and exactly matched the parts in my 1993 Hotpoint dryer. As others have said the pulley kit is not needed--these are included w/ the motor. BTW I am a 53-year-old lady. Thanks to all who took the time to write up their experiences--big help!!

I suspected the idler pulley shaft was worn. I found the repalcement pulley on parts select web site. finding the part was very easy and delivery was very quick. After removing the dryer from the wall,I removed the access panel in the rear which exposed the motor, belt, and pulley. After removing the belt from the pulley, I removed the pully assembly from the dryer. I removed the keeper retaining ring on the pulley and installed the new pulley with the new parts supplied. The new pulley assembly was then ready for re-installation.

What to do if you have a load of wet laundry at 23:00, the dryer won’t start, and you have no spare start switch.
Removed rear access panel and discovered the wire from terminal #2 (goes to heater coils) on the start switch had melted and disconnected. The start switch showed signs of overheating but not melted. Removed the switch and found the switch’s actuator button was jammed in the ‘in’ position (dryer won't start). The switch was a friendly one in that it was possible to disassemble it. Most switches today are molded/glued together, but this one could be pried apart. The contacts inside were still in fair condition and, after dressing them, the switch was reassembled. The actuator button had a burr that was filed off and the switch action worked fine. All of the 1/4" male QC contacts on the switch were cleaned with a wire brush. The burned wire was cut back about 6” and a new piece of 14ga wire was spliced in with a wire nut. A new 1/4” QC terminal was crimped to the wire and all wires were re-attached to the switch.
This fix would probably last for a long time to come, but I bought a new switch and installed it and will keep the old switch as a backup.
p.s. The load of laundry was dry by 02:00.

Unplugged dryer. Removed access door from lower right front of dryer. Disconnected wiring harness to igniter. Couldn't reach retaining bolt with wrench or socket, but was able to spread igniter clip with fingers to be able to remove old igniter and then work new igniter into position without unbolting retaining clip - ultimately a tool-less operation that could have taken 5 minutes. Reconnect wiring harness and reconnect power. Test dryer then replace access cover.

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.