Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DLG3

DLG3 Dryer - Overview

Parts and Repair Help for models starting with DLG3

If you know the dryer repair part you need, you can browse the list of all parts for models starting with DLG3, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DLG3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with DLG3

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$21.73

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils ...

$14.08

Multi Rib Belt - 93-3/8"

This dryer drum drive belt attaches to the motor pully and works the drum as the motor rotates. The belt has a length of 93- 3/6 inches, and wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pully. Replacing the rib belt could solve symptoms such as a screeching noisy dryer when it tumbles, a broken belt (dryer will not tumble if its broken), no heat or not enough heat, and/or the dryer will not start. The tools to use for this repair are a nut driver and a putty knife. Remember to unplug the dryer before installing the part and protect your hands by wearing gloves.

$9.30

Drum Support Roller - for square ported models

This drum support roller is used for square-ported model clothes dryers. It has a metallic bearing in its center. The drum support roller holds the drum in place while it rotates o...

$6.47

Drum Glide

If your dryer is noisy, will not tumble, or is leaving marks on your clothes, you may need to replace the drum glide. The drum glide is installed on the front bulkhead either at the top or the bottom, regardless of the brand of dryer. To gain access to the drum glide, you will have to open the cabinet on the dryer. This drum glide is sold individually but it is important to note that they should be replaced in pairs. Before beginning this repair, it is important to disconnect the dryer from the power source. The tools required for this repair are a putty knife and a 5/16 nut driver.

$32.77

Drum Support Roller

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rol...

$7.69

Idler Pulley Wheel with Bearing

The idler pulley wheel helps the belt to rotate the drum in your dryer. If your dryer will not start, will not tumble, or is noisy during operation, the idler pulley wheel may need to be replaced. This part is located beneath the drum of the dryer, so the drum will need to be removed before you can access the idler pulley wheel. It is also recommended to remove the blower housing and motor from the dryer itself, for easier access to the idler pulley wheel. It is connected by a set of two 5/16 screws. This two-inch-wide idler pulley wheel is beige or black in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center. Be sure to shut off power to the dryer before beginning this repair.

$5.29

High Limit Thermal Fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when ...

$36.37

Lint Filter

Note: This part no longer comes with the felt seal. This filter collects lint as it passes through the dryer vent.

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not centered , clothes getting stuck in dryer

  • Customer: Chris from Hopedale, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 499 of 508 people found this instruction helpful
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new d... read more

The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken

  • Customer: Tim from South Glens Falls, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 485 of 489 people found this instruction helpful
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I th... read more

Filter Lint Was Broken

  • Customer: Mirsada from Yorktown Heights, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 373 of 375 people found this instruction helpful
Took it out of the box and put it in the dryer. I could not find this part anywhere else but on this website. The item was delivered the next day to my surprise. read more