DLB6850AAL Hotpoint Dryer - Instructions

Unplug the AC cord. Open dryer door and unscrew 4 small Phillips screws that hold the top panel to the front panel. Tilt up the top panel.
To remove the front panel: Look on the inside of the front panel, disconnect all the wire connections that go to/from the front panel, such as the light and door switch. Remove 2 screws that attach the top of front panel to the side panels using a 8mm or 5/16" wrench. Undo or loosen 2 Phillips screws at the bottom of the front panel, one at each bottom corner. Remove the front panel. Go to the back of the dryer. Remove the 8 screws holding the lower access panel (8mm or 5/16"). Remove the access panel. Also, remove the 2"x4" access plate in the center of the back panel (2 8mm/5/16"). Reach inside the small panel opening with a needle nose pliers and remove a Cir-clip and washer that holds the rear drum bearing shaft in place. Now you can remove the drum straight forward. Clean, clean, clean the insides. Replace the worn drive belt, follower wheel and front slider pads as needed. Reverse the procedure to reassemble. Plug in and test. Drink beer.

Removed filter as for cleaning. Replaced with new filter. NO TOOLS REQUIRED!

Per suggestion of "Parts Select", I replaced the "high limit thermostat"....very simple task on the dryer: 1 - unplug from power source; 2 - remove screws securing top to front (open door, screws located beneath lip of unit); 3 - tilt top up allowing access to everything; 4 - remove connections to 'thermostat' (note which wires go where); 5 - loosen screws securing thermostat to unit and remove thermostat; 6 - vacuum any and all lint while unit is apart; 7 - install new thermostat and put everything back together; 8 - test dryer to see if repairs worked!

I removed the 2 screws and lock assemblies from both sides on the back. Then i removed 4 screws (two from each side) on the control panel and lifted that up as i tipped the cover forward to disconnect the wires from the door switch. I found the wiring diagram inside the control panel cover, which included a belt routing diagram (very helpful, being the belt was laying in the bottom. I then removed 3 torx srews holding the drum to the bearing, and removed the drum. Let the fun begin! i proceded to put the belt onto the motor pulley and around the tensioner. i needed some help from my wife to set the drum back in as i held the belt up around it. once the drum was back in, i found the beld had fallen away from the tensioner. I lifted the front of the drum up just enough to get both arms below it and move the tensioner back to slip the belt over it correctly. With the new belt on i started to put the screws back in the drum. This got very frustrating, as you have to correctly line up all the holes again, while holding the drum in the correct angle to start the screws. this was the hardest part, not physically, but wears on a person's nerves quickly! Once all the screws were in and tight, i took a deep sigh of relief before i tipped the front cover up just enought to get the wires hooked back up for the door. I turned the unit on to verify the repair before re-assembly. Yep! works again, for well under $20.00! Thanks PartSelect!

Found excellent instructions and diagrams online by searching under the model number. Best of all was the service from PartSelect. Belt arrived 24 hours after ordering. It was the right part, it was easy to install, and the dryer is running beautifully.

Took the top and front off. DO NOT TAKE DRUM OFF!! Lifted drum slightly and worked belt around drum. Replaced front and top. Took off rear panel at bottom near vent pipe. Put belt around motor and then tension pulley. Buttoned everything up and that was it!

Just took it out and installed the new one--thanks so much

I wanted to be sure a replacement would be available when the need arose. The dryer might be 30+ years old. Within a very few minutes I found the filter and placed an order. It arrived in 2 days. Now I won't have to worry about it in this aging lifetime.

Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.

The rear bearing plate had no threads where the screws go to hold it to the back of the dryer drum. I have never bought anything else that needed threads cut in it to be used as a replacement part.

removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.

Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.

I searched the web and found a site that explained how the unit came apart. Took it a part almost according to instructions (I thought I saw a short cut that wasn't).
Unplug
Remove top, torx screws above door, tilt top back, lift front (swing to the right).
Remove clip from back of drum, and slide the drum out(watch the belt or remove tension first)
Remove wires and restring
Slide belt on to drum.
Slide drum back into dryer.
Reinstall front and top.
Retension belt.
Plug back in.
I took the time to remove the duct and cleaned out the unit before reassembly.
Also it helps if you can get easy access to all sides of the unit. I could not, the owner had stored stuff around it to the point that it would have added several hours to the repair to gain easy access. So I had to do some gymnastics to get to all the area's to work on the maching. It is my Dad's dryer and that is enough to write a novel about.
If I had followed the above, it would have saved me an hours worth of time.

First I took the lower bottom off the back of the dryer (bolts), pulled the old pulley off the idler and put new one on. Second, I took the screws out in front (under lip of top) and then removed bolts from bottom of the front. Then lifted lid up and swung front to the side. I was then able to take the drum out and clean it before putting it back in with the new belt. The put everything back together.
Dryer ran for ten mintues and then quite again. Seems to be in the motor and not the less expensive parts I found to be worn.

Open top by removing 4 phillips head screws above opened door, pop top up. Remove rear access panel, remove belt from drive & tension pully. Loosen top front screws, remove front panel to gain access to remove drum. After drum removed, I realized why rear bearing went bad- two front guides were worn causing rear bearing to angle and wear out. Replaced front pads, buttoned her up and now quite as new. Also replaced drive belt while in there.