Models > DDE7209RAL

DDE7209RAL General Electric Dryer - Overview

Sections of the DDE7209RAL

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
D-Shaped Knob Clip – Part Number: WH01X10106
D-Shaped Knob Clip
★★★★★
★★★★★
(27)
PartSelect #: PS268493
Manufacturer #: WH01X10106
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
$6.68
  In Stock
Order within the next 10 hrs and your part ships today!
Rear Drum Bearing Kit – Part Number: WE25M40
Rear Drum Bearing Kit
★★★★★
★★★★★
(17)
PartSelect #: PS267529
Manufacturer #: WE25M40
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
$67.72
  In Stock
Order within the next 10 hrs and your part ships today!
Drive Belt – Part Number: WE12X10014
Drive Belt
★★★★★
★★★★★
(24)
PartSelect #: PS2350043
Manufacturer #: WE12X10014
This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.
$26.19
  In Stock
Order within the next 10 hrs and your part ships today!
Idler Pulley Wheel – Part Number: WE12X83
Idler Pulley Wheel
★★★★★
★★★★★
(6)
PartSelect #: PS265721
Manufacturer #: WE12X83
A dryer's idler pulley wheel serves to help the belt to rotate the drum.
$31.73
  In Stock
Order within the next 10 hrs and your part ships today!
Lint Filter with Frame – Part Number: WE18X26
Lint Filter with Frame
★★★★★
★★★★★
(16)
PartSelect #: PS266250
Manufacturer #: WE18X26
The lint filter and frame for your dryer traps unwanted lint and debris so your dryer can effectively dry your clothes. If the old lint filter is cracked or clogged, or the dryer takes too long to dry...
$37.33
  In Stock
Order within the next 10 hrs and your part ships today!
Door Latch – Part Number: WE1M1011
Door Latch
★★★★★
★★★★★
(14)
PartSelect #: PS3502777
Manufacturer #: WE1M1011
This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on ...
$12.87
  In Stock
Order within the next 10 hrs and your part ships today!
Rear Drum Bearing – Part Number: WE3X75
Rear Drum Bearing
★★★★★
★★★★★
(2)
PartSelect #: PS267865
Manufacturer #: WE3X75
This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.
$12.90
  In Stock
Order within the next 10 hrs and your part ships today!
Adjustable Leveling Screw – Part Number: WE1M642
Adjustable Leveling Screw
★★★★★
★★★★★
(2)
PartSelect #: PS1021358
Manufacturer #: WE1M642
The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able...
$12.16
  In Stock
Order within the next 10 hrs and your part ships today!
Front Drum Slide Kit – Part Number: WE25X60
Front Drum Slide Kit
★★★★★
★★★★★
(2)
PartSelect #: PS267600
Manufacturer #: WE25X60
This front drum slide kit comes with two slides with the apppropriate mounting hardware.
$56.58
  In Stock
Order within the next 10 hrs and your part ships today!
High Limit Thermostat – Part Number: WE4X584
High Limit Thermostat
★★★★★
★★★★★
(4)
PartSelect #: PS268083
Manufacturer #: WE4X584
With this high limit/safety thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. This element is meant as a safety device, will kick back in w...
$32.72
  In Stock
Order within the next 10 hrs and your part ships today!
Drive Motor – Part Number: WE17X10010
Drive Motor
PartSelect #: PS1559768
Manufacturer #: WE17X10010
Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.
$325.07
  In Stock
Order within the next 10 hrs and your part ships today!
Door Switch – Part Number: WE4X197
Door Switch
PartSelect #: PS268004
Manufacturer #: WE4X197
This part has three terminals. Note: Use the two smaller terminals for models that only have two wires to the switch.   No Longer Available

Questions And Answers for DDE7209RAL

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the DDE7209RAL

[Viewing 11 of 11]
Noisy
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Timer will not advance
Fixed by
these parts
Show All
Door won’t close
Fixed by
these parts
Show All
No heat or not enough heat
Fixed by
these parts
Show All
Too hot
Fixed by
these parts
Show All
Takes too long to dry
Fixed by
these parts
Show All
Will not shut off
Fixed by
these parts
Show All
Shuts off too soon
Fixed by
these parts
Show All
Marks left on clothes
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the rear drum bearing was worn the dryer became very noisy
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make sure the wires are not in the way and remove the drum.i also used a vacuume to clean the inside of the dryer. the front drum slides are very easy to replace only 2 screws each.remove old parts install new parts then just put the dryer back together in the reverse order i took it apart. after re-assembly i turned the dryer on it was so quiet running my wife and dogs were very happy. ps. i just want to thank the people at partselect for having all my parts in stock and for the speed in which i received them. other than having to repair my dryer it was a very pleasant experiance.
Parts Used:
Front Drum Slide Kit Rear Drum Bearing Kit Lint Filter with Frame Drive Belt
  • Michael from Warwick, RI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
228 of 265 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer belt broke
first I took the dryer apart 1st thing i did was unplug the power supply (safety first) then I removed the top of the unit then removed the front cleaned all the lint from the inside of the cabinet I found the proper belt size on part select.com the next day I had my dryer belt delivered (which cost 1/3 the price of the local repair shop price)
then I placed the belt over the dryer drum and made sure it was in the general location it should be I then replaced the front cover and the top. then I removed the rear cover which was held on by six 5/16 sheet metal screws which gave me access to the drive pulley and belt tensioner the belt goes on by going under the tensioner then around the drive pulley
Then i rotated the drum by hand to make sure everything had clearance I then buttend everything up plugged it and started it up it workd fine and I figure Ill get another 8 years out of it
Thank you partselect.com
Parts Used:
Drive Belt
  • Matt from La Belle, MO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
151 of 178 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no heat
had to remove top of dryer 2 phillops screws at top in the door opening. flip top out of way take 2 screws out of insides that hold the front on. un hook all plugs and remove front of dryer. once u have did this you need to remove the drum by pulling it out of the bearing in the back un hook the belt from the motor and remove the drum this should expose the element 4 screws and 3 wire to remove it. installation is the same
Parts Used:
Heating Element Coil with Housing - 240V
  • Joshua from Cardington, OH
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
105 of 130 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!