Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DBXR453GV3WW

DBXR453GV3WW General Electric Dryer - Overview

Get Parts and Repair Help for DBXR453GV3WW

If you know the dryer repair part you need, you can browse the list of all parts on the DBXR453GV3WW, or you can search by name or part description. You can also find your part by where it is located on the DBXR453GV3WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DBXR453GV3WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.90

Drum Bearing Slide - White

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This...

$46.04

Front Drum Bearing

This front drum bearing helps your dryer operate as quietly as possible. It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in color. If your dryer model has a light in it, remove the light bulb before removing the bearing because it will hit the bulb and potentially shatter it. This is an OEM part and is sold individually. Please note that although the slides are not included in this part, the drum slides should also be replaced when replacing this bearing.

$6.34

Duct Felt Seal

This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum fe...

$24.29

Drive Belt

This is a dryer drum drive belt. It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps around the drum and a tensioner pulley, and spins the drum as the motor rotates. Your dryer drum cannot spin without this belt. Belts can stretch or become brittle over time which may cause it to malfunction. This is an original manufacturer replacement part. Be sure to use work gloved to protect your hands from sharp internal parts during this repair.

$9.22

Selector Knob with Clip

This knob accepts a D-shaped shaft. Sold individually.

$53.22

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep your dryer running as smoothly as possible with as little noise as possible by supporting the back of the dryer drum and reducing friction as the drum rotates. Over time, your drum bearing will wear out, cause your dryer to be noisy, and you will have to replace it. There may be some sharp internal parts, so be sure to wear work gloves during repair.

$11.10

Door Handle - White

This part is on the outer door of the dryer.

$38.71

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

$37.98

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

$69.06

Lint Trap Duct Assembly

This part includes the duct felt seal (PS9861764) and gasket (PS2577674). NOTE: Per manufacturer this part no longer comes with the sensor bars.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced broken START knob on dryer.

  • Customer: SAM from ROCK HILL, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 488 of 496 people found this instruction helpful
Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.<... read more

The inside of the Selector Knob was stripped

  • Customer: Frank from Irvine, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 377 of 380 people found this instruction helpful
Removed the damaged knob and replaced it with the new knob. Very ease read more

original duct was broken

  • Customer: Chad from Gilbert, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 123 of 141 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3... read more