DBXR453EV0WW General Electric Dryer Parts & Repair Help | PartSelect
Models > DBXR453EV0WW

DBXR453EV0WW General Electric Dryer - Overview

Get Parts and Repair Help for DBXR453EV0WW

Manuals & Care Guides for DBXR453EV0WW

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(142)
PartSelect #:PS755842
Manufacturer #:WE1M504
This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide supports the front drum as the drum rotates. Check both slides f...
$8.42
In Stock
(22)
PartSelect #:PS6447706
Manufacturer #:WE1M1067
The drum slides support the front of the dryer drum. As they start to break down it may cause your dryer to make noise or not dry clothes in the usual amount of time. You will need...
$6.06
In Stock
(28)
PartSelect #:PS960316
Manufacturer #:WE3M26
This front drum bearing helps your dryer operate as quietly as possible. This is an OEM part and is sold individually. It is about 10 inches in height and 22 inches in width. It is...
$41.56
In Stock
(26)
PartSelect #:PS9861764
Manufacturer #:WE09X20441
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum fe...
$7.05
In Stock
(21)
PartSelect #:PS267091
Manufacturer #:WE1X980
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start...
$5.29
In Stock
(71)
PartSelect #:PS1766009
Manufacturer #:WE12M29
This is a dryer drum drive belt. It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps aro...
$32.51
In Stock
(54)
PartSelect #:PS271094
Manufacturer #:WH1X2721
The selector knob is what you use to start the dryer. This replacement knob comes with a retaining clip. This is a very easy repair, the only tool you may need is a pair of needle ...
$12.12
In Stock
(11)
PartSelect #:PS267529
Manufacturer #:WE25M40
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...
$74.45
In Stock
(41)
PartSelect #:PS11767017
Manufacturer #:WE18X25100
This is a lint filter screen that is used for many dryers. It has a metal screen with a white plastic frame, and is approximately 13 inches wide. This part is sold individually. Th...
$35.71
In Stock
(13)
PartSelect #:PS268305
Manufacturer #:WE4X881
This part is used to start the dryer once you have selected a setting on the timer.
$45.83
In Stock
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 724 of 816 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

Intermittant squeaking noise

  • Customer: Mark from Addison, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 587 of 730 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing wit... read more

Replaced broken START knob on dryer.

  • Customer: SAM from ROCK HILL, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 492 of 500 people found this instruction helpful
Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.<... read more