DBLR333ET0WW General Electric Dryer - Instructions

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

removed top by removing two screw inside door,
found felt was out of place and ruined--found some wear on bearing at rear of drum--decided to
replace these parts plus fround bearing--also
new belt ,since it was apart---to remove the drum
you have to remove front panel,which required
removing two bolts from inside at top--front of
dryer just lays down--then you can pull tub out-
I read other customers repair storys ,which made it real easy.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Pull old one out stick new one in. Less than 1 minute. Last repair was the water pump that was easy.

Boyfriend did the repair but it took very little time, the dryer now runs nice and quiet with no thudding and all my clothes are safe from being eaten!

On arrival at rental in Florida, knob & half of shaft are on top of the dryer. Thanks! It's fixed

My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.

I removed the rear panel to access the drive belt. Lowered the pulley to remove the belt and then took off the front panel and popped the top lid off. The belt was slightly frayed on the edges and looked a little old. Inside of the dryer was filled with lint, noticed the vent that sucks the lint from the dryer was almost totally blocked because off caked on lint. Probably from the moisture when we lived in Tx and had it in our garage. Sucked it out with the shop vac and scraped the rest. Removed the whole drum and that's when I noticed the rear drum bearing was totally destroyed and only a piece or two remained. Ordered the drum bearing and drive belt. I was about to put them on when I saw the drum slides were worn pretty thin. So I had to order more drum slides. That's why it took me so long to repair the dryer. If I had the parts already, it would have only taken an hour or so. I was pretty excited that I did it myself, since my husband usually fixes everything around the house. Easier than I thought :o)

It was very easy. Pop out old, connect new wires and done! Can't say enough as to how fast and easy getting the part from this company was. Ordered the part later in the day one night and on the second day the part was there. Outstanding service.

Pulled old lint filter frame out and replaced with new one, very simple. works like new.

i removed two screws and lifted the top up on it hinges. the heating coil was readily accessible. luckly one of the thrmostats fell apart.
partsselect was great. exploded diagrams let me locate and order the replcement easily.

thanks to partsselect i can keep my 16 year old dryer forever.

I repaired it by logging on to parts select website and found the part, waited for about a week or so and opened up the box. I glanced at it and found out that wow it's the exact match except new. Unbelievable and in excitement I went to my laundry room and opened up the dryer and popped that baby right in! Thanks Parts Select

Took off old timer and put new knob on and it fit.