All Installation Instructions for General Electric Dryer DBL333GA0AA

stripped knob on dryer

ordered replacement. received in two days and voila! Fixed!

Parts Used:

Selector Knob with Clip

Sarah from Roswell, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Knob Broken

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

Parts Used:

Selector Knob with Clip

karen from scottsdale, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Start switch broke off

I followed the video instructions. I did have to run to the hardware store to pick up a torx screwdriver but otherwise the instructions were perfect. I generally hire someone to do repairs, but this was too easy! I highly recommend doing this yourself as it is definitely a time and money saver. The website made ordering easy and the part arrived quickly!

Parts Used:

Rotary Start Switch

Pamela from Atlanta, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer making squeeky noise.

Removed the Drum and replaced the part....

Parts Used:

Rear Bearing

NICOLAS from LYNN, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The switch was broken and had to use pliers to start dryer

Disconnected the power removed 4 screws from top panel. Removed 2 wires, turned switch counter clockwise. remopved switch. Replaced with new switch,connected the 2 wires, put panel back inplace,put screws back in panel,plugged dryer back in. SUPER SIMPLE Total time 5 minutes

Parts Used:

Rotary Start Switch

Dan from Fernley, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

plastic selector knob on front of dryer cracked

new knob fit onto 'd' shaped spindle. This took about 30 seconds.

Parts Used:

Selector Knob with Clip

Rita from Cape Coral, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Worn out selector knobs

Took off the broken ones and pushed on the new ones. Simple, simple

Parts Used:

Selector Knob with Clip

KAREN from CHEVY CHASE, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Stripped Rotary switch/broken start knob

Was exactly how the video portrayed… Thank you

Parts Used:

Selector Knob with Clip

Rotary Start Switch

BRIAN from JUNO BEACH, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Worn out dryer knob

I just pulled the old part out using no tools with minimum pressure and pushed the new dryer knob in with no problems at all within approximately 10 seconds.

Parts Used:

Selector Knob with Clip

Jesse from Chesapeake, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

no flame

lift top off, remove front panel and replace igniter.

Parts Used:

Igniter

EMANUEL from WALL TWP, NJ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Thank you for voting!

knob broke

popped the new one on, and works great.

Parts Used:

Selector Knob with Clip

allison from exeter, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Knob broke inside

Replacement knob went on without tools in 1 second.

Parts Used:

Selector Knob with Clip

La Rae from Buda, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Dryer runs but no heat

I first checked the heating element by peeking through the peek hole in the front to see if it was turning on. The heating element turned on but gas failed to flow. Next, I checked all sensors including the fuse, they were all fine. This points to the solenoid as the cause of the issue. So I replaced the solenoids and the problem solved. I did watch the YouTube video on how to check the sensors and replace faulty parts.

Parts Used:

Gas Valve Coil Kit

Mitsuhiro from Anaheim, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

noisy belt

Removed top of dryer, took screws out of back of dryer, pulled drum off front of dryer, removed old belt and slid new one in place. Reattached drum to front and slid belt in place only to find it was the wrong size. Called an appliance repair man, he said happens more ften than not.

Parts Used: