DBL333EY0WW General Electric Dryer - Instructions

a. researched internet to find how to access rotary starter switch
b. isolated all electrical input at breaker box
c. removed 4 torx screws on top of dryer head
d. lowered dryer head (swivels toward front)
e. pulled electrical connections from back of switch
f. turned and pulled thus releasing rotary switch
g. reversed procedure above
h. reconnected electrical
i. started dryer - it worked first time
j. watched football until wife came home
k. told wife dryer was fixed and what a bear it was to get it done :o)
l. that night accepted my reward for working so hard at fixing the dryer and saving us a bundle. :o)
m. now we are both smiling

Troubleshooting was the hardest thing to do in this repair. the first thing I found wrong was the thermal overload was bad. That was easy to replace since that is on top of the housing for the heating coils and easy to reach. Only 2 screws hold it in place. Once I replaced that the dryer would start but, the temperature was off the chart. Now I know why that part broke. The control Thermostat was a little harder. That is held in by 2 screws but it is in an awkward place. I replace the 2 slotted screws with nut driver type screw which made it easier to place the screws in such a small area. Once the control thermostat was replaced the dryer worked great

The part arrived in only 3 days and I didn't even pay for express shipping!

Once I popped the top lid off, and removed the two screws holding the front on it was a breeze from there. Simply take the drive belt off by loosening the spring loaded tensioner on the bottom, lift entire drum slightly up and then out. Remove the screws to replace bearing on rear of drum (4) and the screws that hold the bushing assembly in place (2). Reverse the process and you will be up and running in no time at all.

I was about to buy an ew washer and dryer set, but thanks to PartSelect.com, i saved over $1000!

The only part of the this repair that I struggled with was researching how to pull the front and top of my dryer loose. A putty knife and good instructions solved the problem.
I removed the guides and bottom felt from the diameter of the drum and cleaned the surface by scraping with a razor knife.
I applied the glue and placed the new guides and felt along the drum, securing them with small clamps.

I left the clamps in placed while I cleaned up the inside and behind the dryer.
I reassembled the dryer and let it sit until the next day.
All is well and our drawer are no longer being gobbled up!

Searched dryer model on Google, found partselect.com. Searched for Dryer model and a diagram of the dryer with all its parts appeared. Selected the timer knob on the diagram and it took me to the part, ordered it.
All steps took less than 10 minutes, and I had the new knob in my hands the next day and installed in about 3 minutes.
You saved a few dollars, plus not having to miss time from work waiting for a repair man.
Thank you!
Rocio

Removed front and top panals to dryer. Installed belt over the drum. opened back air vent panal and installed belt to pully. Reinstalled back top and front panals. Done.

First of all I am NOT a do-it-yourself handyman. I unscrewed the panel where the start knob was diagnosed I needed an electrical switch that went behind the panel and a new start knob. PartSelect was great. just plugged in my model number, found the drawings of the model. I selected and ordered both parts for $40. Shipped normal delivery and they arrived in 5 days. I had the parts replaced, the panel screwed back on and the dryer working in 10 minutes. I highly recommend PartSelect for honesty, speed and helpful drawings that allow you to select the correct part. 110% satisfied.

The felt liner between the drum and the front door was worn out. The plasitc glides were all torn apart. Clothes would catch in the rim of the dryer.

Anyways, just lift the lid and tilt the front of the dryer down (after unplugging the control panel). Although only the top of the felt was messed up, i replaced the whole thing. I used the paint stripper to take off the glue residue from the previous felt.

Once it was clean it was easy to glue the felt pieces in place, easy reassembly and the dryer is good as new.

The design of this dryer sucks. This is the 2nd time the felt was repaired. The first time cost well over $300.

Turns out the part was only $50, and the repair was easy as can be...

1. Pop the top cover off, pressing the clips down with a flathead screwdriver.

2. Remove the two screws that hold the front cover in place, and take the cover off.

3. Remove the old glides and the felt they're attached to.

4. Scrape off any remains of the felt and glue.

5. Apply the glue they send with the part. Give it a minute to get tacky before you stick the new part on.

6. Stick the new part on. Let it sit for a few hours before re-assembling the dryer.

Thanks, PartSelect, for saving me a bunch of money, yet again!

Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing).

On arrival at rental in Florida, knob & half of shaft are on top of the dryer. Thanks! It's fixed

used a putty knife to press in the font clips removed top then front panel . pulled off the old felt and glids what was left of them. then used a 2'' air grinder with a 3m scuff pad to remove the old glue and remaining felt then glued the new ones back in place gave it about 30mins to set up then put it back together and works good as new

My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.

Watch the videos for replacing the belt. The one by Kenmore is the most accurate even though it isn't GE -- the mechanisms are the same. Here is the link to the one I found most helpful: https://www.youtube.com/watch?v=G2wTmfurT5o

First: You don't need to pull the washer/dryer out at all. Leave it in place. You can put the belt around the drive shaft and get the tension pully in place by feel and inspect your work with a flasklight,

Second: There is absolutely no reason to spend $70 on a rubber belt. Other places sell it as cheaply as 10 dollars. Shop around -- the actual part is not at all impressive and should not be priced this high.

took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws off the bearing bracket, that's it. easy