DBB3300GA1WW General Electric Dryer - Instructions

I took off the top panel and ran the dryer. I watched as the drum turned more and more slowly until it stopped. I turned it off, and unplugged it.
I took off the front panel, simply swinging it to the left like a gate so I didn't have to disconnect any wires, then pulled out the drum. I should have taken the belt off the pulley idler first!
Got the drum out and could see the broken idler wheel and the groove on the drum's back post for the O-ring. There is a silicon sheath that goes on this back post - don't lose it if it is still good or you'll have to buy another.
Getting the idler wheel off the stem was as simple as using the pliers to turn the nut until it came off. I put the new one on, then put the nut back on. I adjusted the position of the idler pulley so that the belt would not be out of line with the pulley on the motor - I just eye-balled it.
I slipped the belt around the drum, put the silicon sheath back on the drum post, then put the o-ring in the groove on the post.
Put the drum back in the dryer, lining up the post to go back in the hole was a challenge.
Then, getting the belt back on the pulley needed a little muscle to apply the tension needed to allow the belt to get into place. I had one hand in each opening on each side of the drum and did it by feel.
I put the front panel back on and did a test run. The drum was turning with force now, not slowing down nor easy to stop by applying resistance with my hand. It was also much quieter.
Put on the top panel and done!

Uhhhhhh.... Pulled knob off. Pushed new knob on. Took all of 5 seconds.

1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.

I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.

I wanted to fix the cheapest possible problem first which was the thermostat.

Got the dryer apart and it was the wrong thermostat for the dryer, which was good news! I looked in inside floor of the dryer cabinet and saw alot of tiny "springs". Couldn't figure how they got there.

Turned out they were coils from the heating element. Must have burnt out and fell free from the element. So I ordered that and replaced it.

I want to say that I'm in NJ and I ordered that thermostat and got it in ONE DAY! Thought that was too good to be true but when I ordered the heating element THAT CAME IN ONE DAY!

I don't know what kind of people work in the shipping department but they are awesome! You really made the difference on this job.

So did the info on your website. I've never even seen a dryer apart before. It was a piece of cake thanks to you guys. You just saved me about $500.

I was cleaning my laundry room when I noticed the gasket needed cleaning. While wiping it off it appeared as though I could remove it and that was my biggest mistake. Once removed it could not be replaced, due to the little parts that held it to the door began tearing off as I tried to put it back on. I ordered a new gasket and had it put on. It did not require any tools, just concentration. I've learned "if it's not broken, don't fix it"! I spoke with several other people and I am the only one who has removed a gasket. Thank you very much PartSelect for your help.

Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

Read the other posts - they are very good. On my particular dryer it took two Slide WH and two Slide Dryer Drum Side PS266785.

Most time spent was vaccuming out and removing a softball size ball of lint clogging the dryer - now it will actually dry clothes!

Part select delivery is really fantastic (even though it took me three orders to get it right!).

I followed the instruction of the first posting for this category and it worked perfectly...thanks for the nice detail...

- Upon receipt from PartSelect, placed new slides in Drum Bearing (this does not come together or as a kit - must order 4 slides AND Bearing separately for this dryer model)
- Loosened Top panel screws (2) from inside door area
- Slid top of dryer off - PAY attention to HOW the top comes out (tabs at the back and slots on the sides) or replacing the top could prove frustrating)
- Loosened Front panel screws (2) and GENTLY leaned the panel forward to access Drum Bearing - no need to REMOVE the front panel but be aware of the switch wires when leaning and the weight of the door if you did not remove that
- Removed old Drum Bearing
- Vacuumend interior of dryer cabinet (especially area leading down to vent)
- Snapped new Drum Bearing into place
- Re-secured Front panel paying attention to drum position to make sure everything still rotated properly and freely
- Reset Top panel - align back tabs first, gently pull forward just a bit until Top slips down over side tabs, then slide back into place and re-secure

Worked like a charm - took about 20 minutes...

took out broken filter and replaced with new lint
filter.

I had to remove all screws from the back of the dryer, control panel, and one side. Pulled top off. Took out two screws that held front door panel on. Disconnected 3 wires into door and completely removed door panel. Disconneted pink wire from heating element then slide belt off drum as I removed the drum. Pulled off the old completly worn out drum bearing sleeve and replaced it. Replaced drum slides as some were worn through. Had a little trouble getting belt back on when I reconnected everything but for 50 dollars in parts and shipping I have working dryer, so I would say it was well worth the effort.

Unplugged dry cord . Removed top and front cover. Removed drum to replace rear Bearing. Reinstalled drum replaced front bearings and sleeve. Reinstalled both covers and plugged in.

I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

First remove top cabinet panel by removing two small screws under door recess; then swing up lid and remove from hinged area at the rear. Once top panel is removed, remove the front panel and door assembly by removing two attach screws securing front panel to dryer cabinet. Swing the front panel down and remove from two base hinge points. Slightly lift the front of the dryer drum and wedge some rolled up newspaper between drum and frame to provide access to get your hands through to the idler pulley and motor area. Remove the belt form the motor & idler pulley; then slide the drum out of the cabinet to gain access to the idler pulley. Remove nut securing idler pulley from bracket and remove and replace with new part. Reverse the process to complete the installation.

The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.