CVG4280W Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The stovetop gas regulator kept clicking in off position.
The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.
Parts Used:
-
Preben from Fox River Grove, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan stopped working - Switch fell apart
Two screws inside the exhaust box to take out the switch assembly and 2 nuts on the switch. Nothing to it
Parts Used:
-
Barry from Quincy, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad fan switch
Remove switch cover with two screws ,remove two nuts holding switch in place ,remove switch,then reverse procedure with new switch.
Parts Used:
-
James from Hazel Green, AL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
fan switch pushed through, plastic housing broken
Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.
Parts Used:
-
Lois from Alpharetta, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace fan switch
remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.
Then place it back together.
Parts Used:
-
David from Boone, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan started making squeaking sound
I removed cover.and cleaned the inside of the fan housing with brushes and a toothbrush. OBVIOUSLY this made a big mess, but whatever caused the squeaking problem was removed and now the exhaust fan is sounding fine!
Parts Used:
-
Al C from COPPELL, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
defetive fan switch
throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on
Parts Used:
-
john from Ironton, OH
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Parts Used:
-
Yong from Houston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old switch became brittle with age and broke. There were two plastic cylinders that held a spring loaded bearing to operate the contact point. It became brittle because of age and it broke.
I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.
Parts Used:
-
Ed from Escalon, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Parts Used:
-
alphonso from plainfield, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Parts Used:
-
Martyn from Middletown, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Range top fan switch shorted and started to burn.
Turned off power to range top. Two screws to lift the control area. One snap on was burned off.
Removed tab from inside same. Used nut driver to remove switch. Taped wires and restored control area. Power back on. Went to computer and got website for Partselect. Found description of part got me to several choices. The range is 25 years old. Selected a switch that seemed close. It arrived in two days. Redid the same steps. Some file and drill work required to make switch fit. Screwed switch in place. Untaped snap connectors and attached to switch. Checked for function and and restored control area.
Removed tab from inside same. Used nut driver to remove switch. Taped wires and restored control area. Power back on. Went to computer and got website for Partselect. Found description of part got me to several choices. The range is 25 years old. Selected a switch that seemed close. It arrived in two days. Redid the same steps. Some file and drill work required to make switch fit. Screwed switch in place. Untaped snap connectors and attached to switch. Checked for function and and restored control area.
Parts Used:
-
Emile J from Mahwah, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan Switch Broken and being held only by Electrical Wire Connections
removed two screws under fan cover at end of stove knobs. raised panel with knobs up and removed two nuts that held fan switch housing. installed new switch and moved power connections to new fan. (note: Killed power to range top prior to any repair action)
Parts Used:
-
Melissa from Buford, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
switch too big for hole
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.
Parts Used:
-
Darrell from Moultrie, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old grease filter had hole wore through
-
Michael from Mountain Iron, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!