CVE407B-C Jenn-Air Cooktop - Instructions

Simply pulled the old filter out and put the new filter in.

First turn off the power to the stove/oven. Next I removed the 4 screws located on the bottom surface of the control panel. You need to open the oven door to see/access them. The control panel can then be removed by rotating the bottom outward which allows the flange on the top to disengage. Next remove the two screws that hold the switch to the control panel. Note which wire goes to which spade connector. A quick photo can help. Undo the wires. Remove the old switch. Reinstall the wires. Mount the new switch to the control panel. Mount the control panel back into the stove/oven. Turn on the power and test. The burner now works as new!

This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,

The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.

In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.

Thank you for your help!!

Bob

Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!

Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.

The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!

I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

I removed the cover plate for the burner switches and verified the wiring on the other switches. I had removed the bad switch a few years ago and I needed to make sure that the wiring was correct. I did not keep the original screws that hold the switch in place, because I destroyed them when I first removed the old switch. The were corroded from years of cleaning solution. I made new screws from longer wall socket screws by shortening them with a hacksaw. The entire process took about 30 minutes to do, and the results were good. The new switch is smoother than the others, but functions exactly the same.

James is an electrician so he istalled the part himself

Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.

Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.

Used a multimeter to determine that power was going to the surface burner infinite switch. Then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to torx head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed torx screws in the new switch and installed all screws back into range top. Reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.