CTF17PBDL Hotpoint Refrigerator - Instructions

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Could not have been easier. Trick was finding the part for a refrigerator this old, probably more than 20 years.
1. Removed crisper bin. Removed broken cover.
2. New cover dropped right into place. Replaced bin. Everything fit.

Started new gasket soaking in very hot water before removing the old gasket. By the time we were ready to install the new gasket it had mostly regained it's proper shape. New gasket install went smoothly, other than a few of the original clips broke when removing the old gasket.

Wish you gave actual outside measurements of the gaskets so that you don't have to guess the dimensions of ones that are shown overlapping.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

removed the inside fridge electrical panel and swapped switches

I followed the instructions verbatim as others explained. I did it step by step exactly as instructed, The timing was almost exact no more than 30 minutes. I removed the fan the night before the delivery of the new fan and used a small desk fan to cool the compressor. It worked fine in one half hour my freezer read a perfect zero. Thanks for all the help

1) This is a built-in refrigerator with the compressor, coils, etc. at the top. Turn off the breaker to the fridge. 2) Remove the front panel off the top (just push up and pull out). 3) Removed 2 screws to the old timer and carefully remove the plug. Plug the new timer in and screw in. 4) Since our fridge was heavily frosted up, we moved everything to another refrigerator and coolers and kept the refrigerator off until all panels were room temperature. 5) If you haven't cleaned the coil in a while, vacuum it with a soft brush attachment. 6) Turned back on and the refrigerator is cooler than ever!

easy pry out, disconnect wiring, connect on new switch and press in switch.

I opened the refrigerator door, slid the new crisper tray in and I was "in business! You are awesome! The refrigerator is 31 years old and I gave up trying to find parts in Seattle and decided to check on the internet.Thank you. It was all so easy!

repalaced the old one with the new one. easy

I had wasted 5-6 weeks waiting for SEARS to send me the CORRECT Part. They kept sending the wrong part, telling me that the right one would be sent "THE NEXT WEEK" & Then finding out that the CORRECT ONE was on BACK ORDER with NO KNOWN DATE of shipment in Sight! So I looked up the part on the Internet. FOUND PartSelect & THEY found the CORRECT PART(That was on Saturday) with in 3 days... I had the PART! PLUS the Part arrived in GREAT SHAPE-NOT SO WITH SEARS which came with the packaging ALL TORE UP & THE GASKET was half out of the box and BADLY RUMPLED UP! PARTSELECT had very helpful instructions on their site & Over the Phone helped me do it in little or no time at all! I did remove the 2 screws at the bottom or the door-VERY EASY!!! atwhich time I saw that I also needed 2 nylon washers(I had several on hand!) Removing the whole door is not necessary, but in my case I FOUND the very worn washers & Was able to replace them too!... Now the door moves alot easier! PLUS: with the door off, I could do(replace the metal strips)on the Bottom & Inside gasket EASIER!... I WILL NEVER get partsfrom Sears again & ALL of my future Parts Purchases will be from PARTSELECT! I am VERY IMPRESSED & HIGHLY RECOMMEND PARTSELECT!

Replaced fan motor

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Connected the 2 wires and pushed in the switch until it clicked.

per your instructions