CTB1925DRW Magic Chef Refrigerator - Instructions

Thank you PartSelect. Ordered the replacement icemaker for our Amana refigerator, watched the installation video on PartSelect.com. Followed the instructions, took 15 minutes, works like new. Couldn't have been easier.

I went on line looking for information on Amana Icemakers. Found a number of good sources,how to videos.Using the trouble shooting information I found and the how to videos and Parts Select part search to select the replacement icemaker needed for my Amana that was purchased in 1993.Rolled the frig out changed the leads on the water valve. hit the water dispenser and water went into the ice tray: Water valve good.Did a pre-teardown. Unplug Frig.removed ice bucket. removed three sheet metal screws making it easy to rotate ice maker and unplug the power/control cable. Old ice maker out ready to install new one. New icemaker arrives take ice bucket out, transfer on/off bail from old icemaker to new one attach power cable and in about thirty minutes icemaker is bolted in, fill tube in place and prefill ice tray to start the process. In afew hours we were making ice. pitched the first two harvests.Its working like a champ. Have plenty of ice. Very happy with the whole process.

I also ordered a solenoid valve which solved the water dispenser problem. The vidio presentation on your website plus the personal experiences enabled me to easily install the icemaker which solved the leaking icemaker problem. Two small surprises, I thought the electrical wire plugged into the rear of the refrigerator and I didn't know that I would have to cut out part of the icemaker to accomodate for the refil tube. No problem on both surprises. Thanks

Removed ice maker.

Bottom freezer made access a tad awkward.

New unit did not come with wiring harness, or wire rod that activates cycle, or the front cover, which required transferring those items from old unit. Instructions on internet did not address this.

Installed new unit.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.

disconnected electric harness removed screws installed new ice dispensing unit

Researched your web site - determined best bet was to replace the ice maker unit. Ordered the new ice maker and believe it it or not it was here in 3 days and installed EXACTLY as it was stated. Frankly it was a snap and was easier than ever expected. Thanks

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the electric plug.
Then I removed the old unit & replaced it with the new, reverseing the proceedure.

Disconnted current icemaker and removed from freezer. Took off front cover and long arm that control ice dispenser. Put cover and control arm on new icemaker, reconnected bundled wires into new icemaker and clipped along side of icemaker and remounted into freezer. Connnected into back panel for power and checked water supply line to make sure it was lined up properly and job was done. Made sure arm was in down position, had ice cubes in an approx 90 mins.

took off lower bracket, replaced parts, put back together, no more squeek!

It's rather easy and straight foward
(I've done about 3 of them over the years)
take out the ice tray and if you can the top rack (depending on the model of your freezer) for more elbow room. unscrew the bottom screw under- neath the ice maker, then the two top ones, this makes it easier to remove the electrical connector.
take off the old plastic housing(snaps off) put it on new one, take the old wire harness off old, put on the new one, and last take the old wire that turns on the ice maker and shuts it off when full! that pulls out and snaps in the new one, and just reverse the install process!

Turned freez control off. unscrewed singl sheet metal screw, lift off unit, from 2 remain. screws, unplugged
elect connect. Pulled off sm water tube Rmd elect cable unit from old unit, installed on new unit.
Reinstalled elect connect, installed water tube,
Rehung unit on 2 sheet metal screws. Replaced the ice rail[with old one]Turned on freezr control. Had
cubes in 1hr, 4 min... Oh yes, took off old end
decor cover & slipped on new unit .. Greetings from
Hartland, Mi/USA

First I unplugged wiring harness from the inside of the freezer. Then removed two small bolts on top side and one on the bottom. Then took it out of the freezer. Then unplugged the wiring harness from the ice maker. Then plugged it into the new ice maker. Then reinstalled it back into the freezer with the three bolts.Then plugged it back in.