CSX26MRDAWW Hotpoint Refrigerator - Instructions

After replacing the solenoid several months ago, I concluded that the problem could only be the electronic circuit board that controls the timing and delay. The part arrived sooner than I expected. Installing it involved removing only six screws and unplugging two connections. The whole project took only about 10 minutes and now my ice maker works like new. Total cost was less than $55. Saved me several hundred dollars not to mention my personal time had I called in a repairman.

David O.
Albuquerque, NM

used pliers to break revit,installed new shelf left side front is held by screw with phillips head and the back is connected by revit installed new revit.

Note difference between Freezer and Fresh food door.
Also, did not need the Door Stop but should have ordered one water tube union (PS299116). See Freezer below

Fresh Food Door
1. Removed cap at top of fresh food door (Philips screw) and used socket wrench to remove two hex head screws from top of refrigerator.
2. This allowed door to be lifted off base.
3. Removed door stop, hinge shim and broken cam riser from door using socket set and nut driver. Two hex head screws.
4. Replaced all three parts with new parts, re-attached using existing Hex Screws. Make sure cam riser is aligned properly to allow door to fit back on hinge. If it's slightly off, the door will not settle on hinge properly.
5. Replaced door, make sure it aligns properly before tightening Hex Screws to top of Refrigerator. Replaced cap at top.

Same process for freezer door except:
a. At the top of the door, I had an electrical connection due to Ice/water dispenser in the door. This connection is fairly easy to disconnect.
b. There is a drain tube that runs inside the door and through the hinge assembly in the base of the door. The door can not be removed unless the tube is disconnected or cut. There was a Water Tube Union (PS299116) just beyond the bottom hinge which I was able to disassemble to free the tube. However, this took considerable force and luck and I would recommend you consider buying a new part in case it breaks or you need to cut the tube. Otherwise you will not be able to get the door off. Once the tube is disconnected, it easily slides through the hinge and the door can be removed.

My husband did the repair, and even though our refrigerator is roughly 20+ years old, he was able to adapt it to work in all the right spots and we now have ice cubes! I'm very happy we did not have to spend $2000 on a comparable refrigerator.

The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

I had to back-track acouple of times because I put the shelf brackets back in before I had the back panel in.It was also alittle tight getting the thermostat snapped back on the refrigerant line because it is a tight space and I have big hands.For a first timer who has had minimal experiance it wasn't too tough.

I removed 6 screws, unplugged assembly that had motor attached,removed from fridg,replaced motor and reinstalled assembly, putting back 6 screws.works like new.
thanks.

First I replaced the double valve because the ice maker was not filling with water. It still did not work. Then I replaced the ice maker itself. This worked and was relatively easy to replace. I had to use the water fill "slide" from the old ice maker. The new one was too narrow and it leaked water into the freezer.

I used the same steps as described in other descriptions listed here. Since I was changing the hinge assembly on the freezer side the difference I discovered was that there was a nylon water hose inside the hinge assembly that I did not at first know how to remove. I finally called a repairman I happened to know and following his instruction simply snapped the hose loose where there was a connector and placed a cloth under it to catch the moisture that drained. Having done that, the rest of the assembly went just the same way as the other instructions listed here said that it would. Door now functions like new.

I repaired as follows. 1) Open freezer door. 2)Removed ice maker bin. 3) removed screw with broken tab on it. 4) install new shield slide to side.
5) Reinstall screw. 6) Grab TAB (tasty adult beverage) and enjoy on back deck while talking about how good you are at repairing stuff.... HA!

The Ice maker would not run through a cycle. It would fill with water and produce ice but would need a little help by pressing up on the ejector to run through its cycle. Otherwise, it would not bring the ice to the holding bend. Sometimes the water would not fill. The icemaker was making ice it just was not letting the ice maker run through its cycle so I figured it had to be the circuit board. I bought the circut board which was easy to install.
1) Turn off water line and unplug power.
2) Pop off front panel plate at ice cube select switch area.
3) Unscrew 4 screws that holds control panel housing in place.
4) Remove panel assembly by disconnecting two different wiring plugs.
5) Unscrew 2 screws that allows access to control circuit board at end cap.
6) Remove circuit board by sliding it out of the assembly housing.
7) Install new circuit control board in assemble housing and screw on end cap retainer.
8) Attach two electrical wiring plugs.
9) Install control board assemble housing into frig opening and secure with 4 screws.
10) Install front panel plate (pops on).
11) Plug in power and turn on water line.

GE in my opinion made a poor design the ice shelf bracket attached to the metal fan cover after metal tab was bent down that is also where it broke it was riveted to this but the metal broke free
So i purchased a piece of aluminium flat strap cut this about 1" long then riveted this to the shelf bracket and pushed this through the metal fan cover and let rest there and put screw in at other end. Also purchased alum angle also to remake ice shelf when complete then i will use it as ice bucket shelf instead of plastic one.

Removed cowling unpluged timer and pluged in new one.
Great Service, got part in one day

Shut water off to frig...remove cover from back...remove one screw holding solenoid valve. Remove color coded clip on wiring from valve...noting each for replacement. Remove ice machine quick connect water tube, then water dispenser quick connect water tube...the two tubes are different size...so no confusion. Then simply reverse procedure for new installlation.

I removed the back cover on the refrigerator. Unbolted the unit. First of all I unpluged the refrigerator. Took off the two electrical connections and removed the input and output water lines. I then reversed this process when I installed the new part. It was real easy.