CSK27DHZBAA Hotpoint Refrigerator - Instructions

Emptied the ice from tray.
Removed the four screws that hold the face plate.
Removed the four screws that fasten drive housing to the tray.
Slid the drive cup into place at the end of the auger.
Made sure the rubber gasket was in place .
Replaced the four screw that hold the housing to the tray.
Replaced the four screws that hold the face plate.
Put some ice cubes in the tray and tested to be sure everything worked properly.

we took off the old one and replaced it.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

SNAPPED THE NEW SHIELD IN PLACE. DONE!

The gasket I received was stated to supposedly fit my refrigerator, and the box even had printed on it that the gasket was magnetic. However, after going through the difficult process of removing the old one and installing the gasket that was sent me, I discovered that the new gasket WAS NOT MAGNETIC, and would not keep the freezer door closed. I repaired the cracked area on the old gasket and reinstalled it on my refrigerator. When I called Part Select to return the defective part, I was given every excuse in the book, including that the gaskets aren't made with magnets any more, even though the box stated it WAS SUPPOSED TO BE MAGNETIC......just like I was supposed to GET RETURN INFORMATION BY EMAIL that I have never gotten, and my emails are ignored as far as returning it. I WILL NEVER PURCHASE FROM THIS COMPANY AGAIN....

took the old off and replaced with new one very simple . new snapped into place

The internal water line was leaking. I could not find any repair parts for my refrigerator but the GE 5/16 water line was the same size. I purchased 6' of tubing and two unions. Make sure the clean and square. If possible, make the cuts in a spot where you can use the pliers and wrench to tighten the union. I cut approximately 2' out of the existing line and replaced it with the same length of new line using the 2 unions, one on each end. Took about 5 minutes.

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.

Removed the door and installed the cam riser on the bottom of the door.

I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

I had to order bucket as well. Then I removed 3 screws from bottom of bucket and removed auger parts as a unit put new drive cup in new bucket and re attached auger parts as assyembly and reinstalled in freezer.

Replaced broken parts. The ordered parts were received in record time after placing the oreder.

replacing the lines was easy, problem was the drawing on line and the parts list did not show two different size tubing used. had to run out for the 5/16 inche tubing for the water dispenser in the door. got the 1/4 inch tube done in 5 minutes.