Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CSC27HRBAD > Instructions

CSC27HRBAD Hotpoint Refrigerator - Instructions

All installation instructions for CSC27HRBAD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC27HRBAD
466-480 of 613
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Slide Rail Drawers were broken

  • Customer: Denny from Glen Allen, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The ordering process thru PartSelect was simple. Model number got you to the drawings and from there it was " Click to the Cart". Delivery was as expected, but better than most companies. Replacement took only minutes. One thing to remember for future purchases is that hardware does not come along with the part. I had the exsisting screws so I was able to install quickly. I would definitely use PartSelect in the future.

Replacement Of Ice Maker

  • Customer: Craig from Eagle, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old ice maker, then screwed in new ice maker. Only thing that was a little difficult was to hold the auger motor, while trying to unplug the clipped in plug on the old ice maker. I could have used an extra pair of hands.

no water to ice maker or water dispencer

  • Customer: craig from sweeny, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced circuit board and water solenoids

Not clear instructions

  • Customer: Jady from Thornton, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Common sense will take you thru the process of removing, then just reverse the process to replace the auger.

Frig was not making ice.

  • Customer: robert jr from east rutherford, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the faulty ice maker in about two min.. New unit was installed in approx. five min. Watched your video prior to installation and it helped greatly.

rusty auger tainting ice

  • Customer: JoAnn from Argyle, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was so easy! I seldom attempt any household repair because I have a husband that can fix anything, but he was not available. One screwdriver & remove 4 screws attaching the existing front to old auger/bucket. Line up the screw holes on new bucket with old front, put the 4 screws in through those holes tighten screws & I was done.

Noisy fan

  • Customer: Robert L. from Eldred, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

Nit Cooling

  • Customer: Thillman from Hamlan, NY
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Quick repair ,good service . Well satisfied

auger and bucket neded to be changed because of rust which caused the auger and other metal parts to rust which created an unpleasant odor in ice and freezer. to

  • Customer: Joan from Colleyville, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The part arrived promptly but was defective. Upon learning of the problem by PartSelect a new part was shipped and was delivered incredibly quickly. Installing it was easy and took only about 5 minutes. We were pleased with the speed in sending the parts and the ease of installation. We will call on them again if necessary because of their good business practices.

water side not working

  • Customer: Marie from Winter Park, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
pulled out frig unplugged power turned off water at tank disconnected water line and electrical plugs replaced valve replaced wire hook ups different size but easy to install.(came with valve) Cut water lines off inserted into valve different sizes so easy to connect in right place. Reattached electrical wires. (Note remember were the wires came from) Checked for leaks Done! Might want to make sure tubes are inserted completely and you cut the tubes off straight...possible water leak if not.

No problems.

  • Customer: Patricia from Norwood, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

The rail that holds the drawer cracked

  • Customer: Joyce from Bloomsburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just used a screw driver to remove the old part and install the new one. The gal on the phone from parts select was excellent helping me find the correct part. Highly recommend this web site.

The Ice Maker stopped making Ice because the arm over the ice bucket which turned turned on the icemaker was broken

  • Customer: Mitchell from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!

water leakage from water chiller feeder tube(crack in brittle tubing)

  • Customer: adam from Glen Head, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Replaced 5/16 feeder tubing running from chiller out to base of freezer door union.

Icemaker stopped making ice

  • Customer: James from North Billerica, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.
All Instructions for the CSC27HRBAD
466-480 of 613