Switch to Classic
Models > CRSW459P > Instructions

CRSW459P Microwave - Instructions

All Instructions for the CRSW459P
1 - 7 of 7
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
microwave oven blew fuse
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
Parts Used:
Ceramic Fuse - 20 amp
  • tad from tamarack, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
22 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microve stopped working
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise
Parts Used:
Ceramic Fuse - 20 amp
  • Denice from Montgomery, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
11 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave went pop and nothing would work.
I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.
Parts Used:
Ceramic Fuse - 20 amp
  • Deborah from STRUM, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Died while heating lasagna
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.
Parts Used:
Ceramic Fuse - 20 amp
  • connie from madison, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
9 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
tray glass floor broke
Remove old tray, clean old caulk, and clean inside of microwave, Place new tray-glass floor and caulk with heat resistant silicone. Easy project.
Parts Used:
Glass Floor Tray
  • Eduardo from baltimore, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken tray-glass floor of microwave
very simple job. removed broken tray, inserted new tray and caulked around edges with a high heat resistant caulk.
Parts Used:
Glass Floor Tray
  • ted from lagrange, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to any microwave functions
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!
Parts Used:
Ceramic Fuse - 20 amp
  • Richard from CALIFORNIA, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CRSW459P
1 - 7 of 7