CRD22EY-3A (5M74A) Amana Refrigerator - Instructions

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!

Took out socket, replaced new bulb in new socket and plugged in. Easy!

Unloading the freezer and removing the back panel were the most time consuming aspect of this repair. Many models only have 4 screws, but this one has 9, and being a side by side it was a tight fit to reach them. Once defrosted we tested the thermostat, found it "dead", and ordered a new one. The part came within 3 business days. Installing it took minutes, since we had not permanently screwed in the back panel again. We didn't want to reload everything until we knew things worked properly, so we didn't put everything back right away. We thought we had further problems as the freezer got really cold but the frig still didn't get down to temp. Turns out we just needed to reinstall the fan shield which we'd taken off along with other parts to access and check the vents. The fan shield must be in place to direct the cold air into the vent to the refrigerator. Duh! It was an oversight that once caught made total sense! Now all works fine on this 20 year old Maytag side by side!

Pull box out ""unplug box"" empty frezer including storage baskets,place ice maker in off remove ice cube box, do not remove ice maker, useing nut driver loosen side rail screws about 1/4"slide basket rails in or out and pull to center of box should slip off screws, remove light bulb cover & bulb, remove 4 screws holding ice worm drive motor "" hold "" will fall it is atached to a electrial plug un plug and lay aside,unscrew back panle screws 4 left 4 right on back cover, " remove hiden screw at top center of back panel and pull up and pry out at bottom silde out downwerds,remove cross plates one center one bottom these hold defoster bars, unwind wires center defroster bar somewhat difecult bottom one just slide down unplug from panel at top behind where ice cube drive was located, replace new defroster assm reasemble defroster bars into cross bars wind in & plug up new wires behind cooling fins being carefule not to cut or nick wires of bend cooling fins replace screws,wires are 1 small plug 1 large,reinstall back panle top center screw first don't tighten aline side screw holes replace side screws then tighten top screw. Replace drive motor being sure to conect,replace bulb,bulb cover,side railes,bens,ice cube box & put ice maker lever in on poss. Plug box in weight 8 to 10 hours with box set at mfg 's starting settings. Should work like a charm.

I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!

I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!

pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I removed the cover that protects the freezing tubes, they were frozen solid,used my heat gun to melt away the ice, being very careful not to burn any wires. Then I removed the old heating coils,connected the new ones, replaced the cover and I was done. The thing that took the most time was melting the ice, you cant do it in a hurry because you may burn wires

Pull out plastic cover #13of refrigerator part discription (temp. control and light socket), snap out old light socket and replaced with new light socket. light is now working.

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

just had to remove the fan motor the hard thing is getting down to it

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.