CRD22AY-3A (5M74A) Amana Refrigerator - Instructions

although this piece s white, my refrigerator had clear plastic guides - both work OK. Remove meat drawer, remove glass shelf from refrigerator. Glass shelf is attached to metal frame by two clips at rear of shelf. Before removing, notice how the clips are fastened to the chrome trim so replacement will be easier. Remove clips with fingers. Glass shelf will then swing up and away from metal frame, allowing easy removal of drawer guide(s). Remove broken guide and replace with new. Lower the glass and re-attach metal clips. Replace metal shelf in refrigerator and re-insert drawer. That's it.

I removed the drawer, and removed the shelf and both rails. In the back were 2 clips to secure the shelf to the frame and stabilize the rails. Then I could move the glass shelf and access the broken rail and replace it with the beautiful new one. I feel like I Have a new fridge! I found the part on line even though I could not find the plate with the model number or year!

I have to say the packaging of the diary door was A+++ It took less than a minute to snap out the old door (that I had tried to hot glue) and snap in the new door. My story is what a fantastic sales department you have. I submitted my order for the dairy door as well as new shelving hinges. The hinges came in right away; however I received an e-mail saying they no longer had the dairy door. I received a message on my cell phone that the sales lady She said she located a couple of dairy doors in other warehouses and was going to check their availability. Sure enought, it took a week or so, but she did come through with the dairy door for me. I was told they only had a couple left and that they were not making them any longer. Whoever this sales lady is.... three cheers for you what an excellent job. She really did not have to pursue the order any further than her own warehouse but she did - thank you for your excellent service!!!

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

Took out the old drawer and slid the new one

I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabinet on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.

Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.

I tilted the unit back enough to scew the new legs into the threaded holes.

I called a local appliance store in town to get a replacement shelf.They did call me back and stated they could not find anything. I found this web site and (had my husband re-measure the size) ordered it on line. I received it in 3 days, and would strongly recommend this web site to anyone.

Simply inserted the shelf. So easy to find just what we needed from the website. We really got great service and the shelf arrived in three days. Thanks so much.

Screw bulb in and place cover over bulb.

Pull out plastic cover #13of refrigerator part discription (temp. control and light socket), snap out old light socket and replaced with new light socket. light is now working.