Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CMV1000ADW > Instructions

CMV1000ADW Maytag Microwave - Instructions

All installation instructions for CMV1000ADW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CMV1000ADW
1-15 of 42
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burned out bulb

  • Customer: john from plainfield, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 27 people found this instruction helpful
removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

microwave oven blew fuse

  • Customer: tad from tamarack, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 20 of 28 people found this instruction helpful
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

Burned out light bulbs in microwave hood stove

  • Customer: Herbert from Norton, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 23 people found this instruction helpful
I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.

outer handle on microwane

  • Customer: charles from round rock, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 16 people found this instruction helpful
removed trim around inside of door with putty knife.
disconnect latch spring with needle nose plyers.
remove two handle screws.
remove small screw on handle to separate outer handle from inner handle.
replace outer handle and assemble with inner replace screw.
connect handle in door
snap tim back into place

no heat

  • Customer: Lisa from PARADISE, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 13 people found this instruction helpful
I looked up the #1 reason for no heat for my microwave on the site , and using my model number found that 92% of the time it was the Black Sleeve Diode. Ordered the $15 part, and installed it within 30 minutes. Most of the time was used for removing the built in microwave and removing the cover. Replaced the diode by finding it on the diagram that I printed from this site (free). Very relieved that we don't need to have our custom cabinetry re-sized to accommodate a new microwave. Thank you!

Glass turntable tray was broken upon unpacking the unit

  • Customer: Janet from Remus, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
It was just a matter of setting the glass tray on the turntable in the microwave, so there is no story there. However, I am properly impressed with your service. I ordered the plate one day and had it the next. Outstanding!

microve stopped working

  • Customer: Denice from Montgomery, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 11 of 17 people found this instruction helpful
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Died while heating lasagna

  • Customer: connie from madison, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 15 people found this instruction helpful
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Microwave went pop and nothing would work.

  • Customer: Deborah from STRUM, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

two tiny plastic posts, which cracked or broke resulting in door handle almost falling off

  • Customer: Corley from Fort Stockton, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
My son-in-law took the handle off. We saw the problem (Maytag put two tiny plastic posts that crack about once a year. This was the 2nd replacement in 2 years.) When the new part came in my 15 year old grandson put it on easily. This is a no-brainer!

Door handle snapped off where screws attach

  • Customer: Dan from Riverview, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I pondered getting both the inside and outside parts but went with the outside only. Prying the gasket loose went very easily, and removing the latches went easy too (to expose the bottom screw. I found the inner handle base broken but glued it together, not worrying too much because the real attchment to the door is done with the outer handle screws. I can see why the handle broke in the first place because the screws went in with a lot of torque necessary. I suspect that this weakened the posts so I lubricated the screws and backed them in and out so as not to stress the posts. I think all that is necessary is the outer handle, if you want to save some money. Everything snapped back into place easily and it is done after listening to the wife complain for almost 6 months. Part Select is a great site for appliance repair.

light bulb burned-out

  • Customer: Pablo from Burlingame, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 23 people found this instruction helpful
screwed in new bulb

No power to any microwave functions

  • Customer: Richard from CALIFORNIA, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

Old handle broke

  • Customer: Anne from MIRAMAR BEACH, FL
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
First, I didn't realize that there were two parts to the handle. I ordered what I thought was the handle and then had to order an inner handle after I had taken the old handle off. I'm an old, not very agile lady, with minimum experience and ability, so I did struggle. I would strongly recommend a screw drive which has a magnet, as it is really difficult to put the screws which fasten the handle, back into the handle. Feel very proud of self tho, because I did do it, and now it works!

Burned out light bulb which lit the surface of the range.

  • Customer: Michael J from LORAIN, OH
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.
All Instructions for the CMV1000ADW
1-15 of 42