Models > CLZ8560ADQ > Instructions

CLZ8560ADQ Magic Chef Cooktop - Instructions

All Instructions for the CLZ8560ADQ
1 - 12 of 12
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The grommets came apart metal from rubber.
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.
Parts Used:
Rubber Grommet
  • Frank from Pierce, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
23 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
range top loose, grommets missing
very easy to push each grommet into range top holes
Parts Used:
Rubber Grommet
  • joseph from wildomar, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light
saw burner tube was completely rusted at end and would not line up with burner. decided to go ahead and replace all three tubes. was easy to install, able to get a good cleaning job on unit in the process. works fine, wife is happy and that is what matters in a motorhome.
Parts Used:
Flashtube Extention - Front
  • Albert from Clewiston, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
11 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing gromet
Pushed into hole by hand, really simple
Parts Used:
Rubber Grommet
  • Hal from National City, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't ignite
Pulled knob,removed 2 screws removed wire,removed old ignitor repl. With new reversed procedure,done
Parts Used:
Burner Control Valve with Igniter
  • William from ARCHER, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter failed
The igniter on our RV stove top failed after 4 years of operation. The repair took about 8 minutes and everything works fine.
Parts Used:
Burner Control Valve with Igniter Range Surface Burner Igniter Wire Harness
  • Paul from Niland, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost on of the Rubber Grommet holding the stove grate
So simple would be embarrassed to give any instructions; it is so self evident.
Parts Used:
Rubber Grommet
  • Martin from Millersburg, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
flashtube was burned off
put in new flashtube
Parts Used:
Flashtube Extention - Front
  • john from mount vernon, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Rubber grommet for stove top cover
I ordered the grommet... Didn't match the others ... But it fit on , and will do the job
Parts Used:
Rubber Grommet
  • Lisa from Plymouth, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
range top was missing one of the rubber grommets used to hold the grate.
Just pushed the new grommet into the hole. The grommet fit just fine and took about 10 seconds to install.
Parts Used:
Rubber Grommet
  • John from Elizabeth, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Wore out parts replaced
Put new parts on & the only trouble I had , I had no ideal where the or how the Extension flash tubes went on had to take one of the burners off & looked it over & found out it had two little what I`ll call slices in it to put the tubes on after that it all went in place very easyly it all worked just fine
Parts Used:
LGHTR-BRNR Flashtube Extention - Front Flashtube Extension - Rear
  • Alvin from Hudson, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
original grommets broken
The new grommets were NOT the correct parts, too big, so there was no repair.
Parts Used:
Rubber Grommet
  • William from Richwood, OH
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CLZ8560ADQ
1 - 12 of 12
Back to Top