CG206B Jenn-Air Cooktop - Instructions

Repair is simple as long as you TURN OFF THE CIRCUIT BREAKER first. After that, take off the cover over the switches (pull knobs off, remove 2 screws and lift off the cover), pull the bad switch straight up off the gas valve, pull the two wires off the switch, plug them back onto the new switch, place it back over the gas valve stem, reassimble the cover and knobs, turn back on the circuit breaker, and verify that ignition switch works. Not a hard repair. (HINT: while you are waiting on the replacement part, you can light the bad burner by turning on the opposite burner ignition switch and using that "spark" to light the other burner.)

Turned off the gas valve and disconected the gas line from the stove-top. Removed the stove top and disassembled the unit, to access the bad parts. While unit was disassembled we cleaned the parts which were to be reused and applied the new parts. The unit was then reassembled and reinstalled. The replacement of the gas valve required only a 1/2" wrench and screw driver, while the replacement of the ignitors required the use of an adjustable wrench. The ignitors are connected via spade connectors to an electrical device located in the electrical box at the lower center portion of the unit. Not a hard job but slightly time consuming.

I did only tokeout the four tips balves like a screw 1/2 in. And replace the otherones and is it. Less than 5 minutes for all four to replace

unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.

I turned off the burner and allowed it to cool. I then checked the website for the part and also got a new grease filter and grill grate. When the parts came, I plugged in the new grill burner, replaced the grill grates, and dropped the filter in place. Total time was about 8 or 10 minutes--most of which was opening the packages. The grill burner is designed so that it can be removed and replaced with a standard 2 burner unit. No tools were needed. I was glad to find the parts for my 17 year old dual-fuel range.

I removed the screws that hold the escutcheon assembly in place and lifted it from the range top. I slipped the wire connectors from the old switch and removed the push nuts. Removing the push nuts was the most difficult part. I wedged a small screwdriver under them and made enough space to cut them off with wire cutters (DON'T CUT THE POLES THE PUSH NUTS ARE ATTACHED TO!). There may be an easier way to remove them, but I'm a rookie and don't know what the easier way would be.

I attached the wires back to the same poles on the new switch as they were positioned on the old switch and pushed on the push nuts that came with the new switch to hold it in place. There isn't much room to work with so I used a small socket from a socket wrench set to hold the new push nuts in place while I pushed them on. The push nuts I received with the new switch were really too small. I forced one on, but broke the other one. I bought another slightly larger one at my local hardware store and it worked great.

I reattached the escutcheon assembly and was back in business. Overall, it took me about 30 minutes.

My husband threw a pot holder on the hot (not lit) burner grate.The potholder melted on the grate and we were not able to remove the melted fabric. We ordered a new grate and it looked so good we ordered three more. I am planning to replace the burners next. We'll have a brand new looking cooktop. The cooktop is 15 years old.

In oven I unscrewed orfice; replaced with new orfice. On stove top the people who make it sent a kit for $11.00, plus S & H. I installed it as per instructions.

pull off old ,add new

I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.

This wasn't a repair; it was a desperately needed replacement. I simply popped off my old knobs and put the new ones on in less than 1 minute. The new knobs took years off my beloved gas Jenn-Air stove.
The knobs arrived within two days of placing my order. Outstanding customer service. I will order from this company again and again.

I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net

Turn off the power to the appliance. Remove the two screws from the control panel. Turn the panel over leaving all wires attached. Others have complained about the difficulty in removing the old push nuts and installing the new ones – this way worked quickly and easily for me: to get the old nuts off – take an awl and wedge it between the flat part of the push nut and the plastic mounting tab of the switch body. Pull the awl upwards until it is parallel with the mounting post. The push nuts will break, use needle nose pliers to remove the broken push nuts. Pull the old switch out noting the orientation. Place the new switch in place over the mounting posts. The new push nuts are not too small, it just takes some force to get them on (a good thing, it keeps the switch in place). Easy way to get the new nuts on: take a small nut driver that is the same diameter as the new push nuts on a straight handle, and use it to force the new push nuts onto the posts. Move the wires from the old switch to the new one. Turn the panel back over, replace the two screws, restore power to the appliance. It is a 10 minute job with the right tools.

removed 2 screws to access the ignitor. Discinnected the wires from the old ignitor and slid the old ignitor off. Installed the new ignitor and attached wires.

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.