CG206B Jenn-Air Cooktop - Instructions

I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

Removed four screws; withdrew two burners; set two new burners in place; installed same old screws. That was it. When I turned them on to adjust the flame, they came on almost instantly and no adjustment was needed.

Wife loves the nice new look.

pull off old ,add new

The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.

Contacted customer service via email. Included a description of the problem as well as a photo that clearly showed that the Front Burner Assembly was, in fact, NOT an assembly when it arrived.

Nobody even acknowledged my email.
This was a $140 assembly.

Never again will use these guys for repair parts.

This wasn't a repair; it was a desperately needed replacement. I simply popped off my old knobs and put the new ones on in less than 1 minute. The new knobs took years off my beloved gas Jenn-Air stove.
The knobs arrived within two days of placing my order. Outstanding customer service. I will order from this company again and again.

I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net

I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.

removed 2 screws to access the ignitor. Discinnected the wires from the old ignitor and slid the old ignitor off. Installed the new ignitor and attached wires.

Turn off the power to the appliance. Remove the two screws from the control panel. Turn the panel over leaving all wires attached. Others have complained about the difficulty in removing the old push nuts and installing the new ones – this way worked quickly and easily for me: to get the old nuts off – take an awl and wedge it between the flat part of the push nut and the plastic mounting tab of the switch body. Pull the awl upwards until it is parallel with the mounting post. The push nuts will break, use needle nose pliers to remove the broken push nuts. Pull the old switch out noting the orientation. Place the new switch in place over the mounting posts. The new push nuts are not too small, it just takes some force to get them on (a good thing, it keeps the switch in place). Easy way to get the new nuts on: take a small nut driver that is the same diameter as the new push nuts on a straight handle, and use it to force the new push nuts onto the posts. Move the wires from the old switch to the new one. Turn the panel back over, replace the two screws, restore power to the appliance. It is a 10 minute job with the right tools.

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.

The repair was super-easy, the hardest part was removing the old screws and switch. I slid a putty knife under the old switch and used that to pry up while I unscrewed the nuts. The new switch was a very snug fit on the two studs, which was nice, but the nuts included with the new switch were too small as-is. I could have driven a punch through to increase the diameter, but I kept my old nuts and re-used them instead.

Since the other three burners sparked, I traced the problem to the switch on the valve shaft. To replace, (after unplugging the power cord) I pulled off the knobs, removed the two screws on the valve cover (inside the downdraft vent) and pulled the switch up the shaft to remove. I transferred the spade terminals to the replacement switch, oriented and installed.

1. Turn off power to the cooktop and turn off the gas. This is extremely critical. 2. Remove the knobs and then the covering. Beneath will be the valve part you need to change. 3. Find a way to mark where all the wires go into the piece that sits over the valve (mine was white with a blue ring in the center). You will see four wires going into it. You can photograph it, or you can use tape and a sharpie to write where everything goes on the parts themselves. It is likely that they will become disengaged at some point during your repair, so the step is crucial. 4. Lift off the piece on top of the valve (the valve goes through the blue hole in the center of the white piece). Don't be afraid to give it a tug, as it can be slightly stuck. 5. Find a way to get underneath the large circular plate (mine was gold colored) beneath the valve in order to remove any screws that are holding the valve in place unseen below the surface. 5. Now back above the surface: disconnect the gas valve attached to the valve. 6. Switch out the valve to the new one and reverse these steps to install it. ****7. If you are unable to get beneath the plate where the valve is attached on the underside, no worries. Take the new valve and carefully unscrew the top two screws (need a special tool from a hardware store) and similarly take off the screws on top of the broken valve. Be very careful to remove the top of the old valve slowly enough to see exactly how the inside pieces have to be put together. Essentially, you will find a spring and a small ring with three notches. The small part of the spring goes on the bottom, the larger part of the spring faces upward, and on top of that goes the ring with the three notches aligned in a certain way that's very important so that when you put it back together not only will the valve depress properly but you will be able to change the fire from low to medium to high. Make sure you can depress the valve a little bit, if not you have to readjust the ring until it's in the proper position. 8. Turn on gas and power to be sure it works. 9. Close unit. ***Note: if any of your parts accidentally dropinto the opening, use a magnetized srcrewdriver to retrieve them.

The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.