CG206B-C Jenn-Air Cooktop - Instructions

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

No problem, except the holes in the clips to hold the switch in were so small that the clips would not go over the pegs.
The solution - use supper glue.

Replacing the side grill burners was easy--lift off the grill covers and pull out the grill burners. Next, attach the new front and rear burners to the burner plate with 2 screws (the older version uses 4 screws) using a nutdriver. Place the 2 burner unit (now joined) into the 2 gas inlets (no screws necessary--just slip them over the tubes). Insert the grill pan over the burners and place the 2 burner grates over each burner. Done!

Turn off the gas supply and unplug the electric supply. Remove the top grates and the burner cartridges. Remove 12 screws around the top cover and loosen the two screws for the fan switch. Pull the fan switch up and out of the way, remove the top cover. With a marking pen, label the four igniter switches and pull them off the gas valves. From underneath, remove the gas line from the pressure regulator, then remove the regulator from the pipe coming from the circular manifold. With a 3/16 socket (1/4 inch drive) or a 3/16 nut driver, remove the four screws that hold the manifold. Then from the top pull the manifold up and out. On the bottom, remove the screw (1/4 inch socket or nut driver) and remove the old gas valve. That's it. Now just put it all back together in reverse order. I used pipe joint compound on the pipe threads. Check for leaks with a soapy water solution. If I had to do this again, it would only take me half the time. I wasn't sure how everything came apart the first time..

unscrewed previous unit, placed new unit and screwed in place.

Removed old burner, replaced with new one, works perfectly! Only one screw to take out and use with new piece.

So very easy!!!! I'm a 70 year old grandmother with a small socket set - and that's all I needed! Removed one small screw, removed old burner, popped new burner in, replaced one screw, and back in business! Placed order, received it in 2 days, fixed burner. So much faster than calling a repairman!

Inside the knob, I placed a dab of CA glue on the small plastic projection , which was designed to press against the metal post, but was just shy of it. By thus building it up the knobs function perfectly.

The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.

The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!

Easily removed the switch housing. After that, the other experiences really helped me as the retainer rings on the old switch would not come off and I broke one of the threaded posts about a eight of an inch from the base. I pried the other one off, more carefully, with a screw driver and a vice grip pliers . I was already to use the "super glue" solution when I luckily found an old nut that fit the one remaining threaded post.

Took less than 15 mins to remove the old switch and replace for the new one.
Works like new!

Nothing really. Only couple of screws to attach the bracket holding the front and back burners.
The other parts: filter, burner, pan, where just replaced.

Called Parts select and they replaced it in two days.

Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!