CEX650VX0 Roper Range - Instructions

Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.

Pulled out element, plugged in new element. About 5 seconds.

Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element making sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.

Lift and remove heat elements
Lift and remove Drip bowls

Replace Drip bowls and heat elements

I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.

The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.

I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.

I have reinstalled the earlier unit.

Is part# PS 11744446 no longer available?



James E Weimholt. jmwm4031@verizon.net

Pulled out the old burners and put in the new ones.

I followed the instructions provided.

The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!

i just unpluged the old burner and slideed the new burners in place and they work great now like a new range

Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connected them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.

Unwrapped package. That was the hardest part. Inserted into the little spot on top of stove. Tested. Worked great!

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

Shut off power to the stove.
I removed the screw that held the block in place. Then I lifted the top of the rage to get to the wires. I cut the wires from the old block and stripped back the insulation. Next I put the heat shrinking sleeve on. I attached the new block with the wire nuts, pulled the sleeve down and used a hair dryer to shrink them. Then you just hook it back on screw it in and your done.

I took the old wires and plug off and replaced it with the new block it works fine

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan