CEH343001 Frigidaire Range - Instructions

Cut the old block off tied new wires to hot wires . That easy!

Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

Bottom oven quit heating about 6 mos. ago and now top oven quit. Broiler worked fine on both. Bought 1 replacement element to try. Did not work on either oven. Found online where someone had found a bad solder joint on a relay board so I pulled the oven and removed the covers. (WITH POWER OFF. I made a diagram of the wire connections to the board and removed it. I FOUND a cold solder joint on the L2 connection of the top oven board. I found the exact same cold solder joint on the bottom oven board also. After resoldering the connections and touching up any suspect joints I replaced the boards. They BOTH WORKED fine!
Anyone that can't solder can take the boards to a local radio/TV repair shop and probably get the techincian to resolder it for a minimum fee. It is certainly worth the attempt.

We pulled the stove out from its slot in our island. We unplugged it and unhooked the gas line so we could get behind it easily. We then took off the back (using screwdriver) to get to the connectors for the element. We unhooked the connectors from the old element. Then we took off the plate inside the back of the oven (using screwdriver)and gently pulled the old element out. We seated the new element in the oven and then hooked it up in the back and put it all back together again. It worked perfectly! The hardest part was cleaning the dirty floor under where the oven had been for 7 years!

Unplugged the element and the melted on pot. Plugged in the new element. I thought I might need a whole new cooktop but a new element was very easy to find online.

I unplugged the damaged unit and plugged in the new one.

First I unplugged the element that wasn't working and switched it with one that was to confirm that it was the burner element, and not the cooktop wiring, that was the problem. Once that was confirmed, I ordered a new element from partselect.com. Upon arrival of the new element several days later, I plugged it into the empty plug on the cooktop and voila, we're cooking on all 4 again.

It's kind of embarrassing!
As the breaker was being thrown to turn the current off, I discovered that the breaker box was burn up at the breakers.
Short story but I got'er done! The problem now is there is something still wrong with teh oven!
I think I see a new one in the future!
Thank you very much for the very prompt delivery.
My purchase has been without a flaw.
I have already sent the part back for a refund.
It cost me something like $13 for this experience for freight.
I will remember you with my next need.

I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!

Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Took screws loose, unplugged old one plugged in new one put screws back