Models > CDU210CWW > Instructions

CDU210CWW (P1199014W) Caloric Dishwasher - Instructions

All Instructions for the CDU210CWW
1 - 12 of 12
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Spring that holds door closed
First, removed screws on bottom panel. On this model, everything was easy to see. Did not have to move the appliance at all. The left side wire was broken. Just removed the broken part, connected the new wire, and then the springs to it. No problem at all. Took about 15 mins.
Parts Used:
Cable and Eyelet
  • Bessie from Fruitland Park, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
10 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn"T Drain The Water Completey
Removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. . . )
Parts Used:
MOTOR-PUMP
  • clarence from ST LOUIS, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door mechanism broken
First removed the two screws and then the bottom part of the door. Replaced the broken cable & eyelet assy with the purchased part. Connect the eyelet with the two springs which tied with door mechanism with other cable/eyelet assy. Done
Parts Used:
Cable and Eyelet
  • Chung from Petaluma, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door spring broken
It was really easy- Loved the fact that you had a picture of the part needed on your website, it really made finding the part we needed very easy. I would highly recommend your site- the part came quickly, also
Parts Used:
Cable and Eyelet
  • Tracy from Montour Falls, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two upper rack rollers were broken
Used ascrewdriver to bend the metal rail that the roller rolls on. The part that needed to be bent holds the end cap on. Once bent, the end cap pops off. The the old roller can be removed and the new roller instsalled. The rail then needs to be re-bent.
Parts Used:
WHEEL
  • Duane from Seattle, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper rack roller cracked then broke
First removed the end cover and clip on the end of the rack slide. Used a flat head screwdriver to push in the clip and carefully pried it out. Then using the same screwdriver, pried up on the rack roller clip attached to the dish rack. Once clip was free of the rack, slid the rack roller off through the front of the slider. Slid the new rack roller into the slider and snapped the roller clip onto the dish rack in the same place the old one was. Carefully twisted the plastic end cover and clip back onto the rack slider. Job complete. The trickest part of the job is removing the rack slider end cover.
Parts Used:
WHEEL
  • Jeffrey from Wilson, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
original wheels were broken
I first removed the rail end caps by bending open the rail ends. They easily come off. The wheels slide out of the rack and the part snapped on to the rack removed. I used a screw driver to pry them off. New wheels are slid into the rail and snapped to the rack. End caps put back into place and rail tips bent back. Very easy.
Parts Used:
WHEEL
  • Todd from Powell, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
upper dishrack fell not supported
Removed the end cap from the rack guide.Removed broken roller and stud.Slid on new rollers and studs attached to dishrack reinstalled end caps.Total time less then 15 minutes.Easy job.
Parts Used:
WHEEL
  • Carl from Bradenton, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front plastic Piece on both top level slides wouldnt come off
It would have been nice, not being a dishwasher repair man, that when the new parts came, there were a set of instructions included on how to install them. There must have been a special tool that Maytag uses to repair these items, and I ended up having to break the pieces off in order to install the new parts.. this was a shame.

I installed the rollers that allow the top tray to slide in and out of the dishwasher so I can lay glasses and pans on that shelf... There are 2 plastic white pieces in front of each slide that must come off in order to slide out the old parts and in with the new.
But I had to twist each plastic side real hard and break them to get the new parts in.. now I have a mess...
Parts Used:
WHEEL
  • Harold from Snellville, GA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Parts Used:
Screw
  • Kathryn from Carol Stream, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump seal elak
Removed motor and found shaft severely rusted. Cleaned up the rust but the shaft was too pitted to work effectively with the new seal.Wasted my time and money
Parts Used:
SEAL-PUMP
  • Richard from Northville, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cable for door springs broke
Attached new cable and eyelet to existing springs. Took all of 5 minutes to install. Very easy. Works great.
Parts Used:
Cable and Eyelet
  • William from Philadelphia, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CDU210CWW
1 - 12 of 12