CCG406B Jenn-Air Cooktop - Instructions

the hardest part of the whole thing was finding the part... partselect.com made it easy. the part was delivery quickly using regular mail, and I was simply able to slide the new knob on.

Simply pulledoff and threw away the old bad knobs and slipped the new ones on in thier place- four working burners now!

Most amazing thing was I ordered the parts one afternoon and they arrived the very next day.

Also, your site was easy to navigate and find what I was looking for. Many thanks!

threw out the old and slipped on the new dial....

Went broke purchasing the very simple part through you PartSelect Appliance Parts

Replacement parts fit as suggested by model number (newer parts are a little different but fit fine). Grates look a bit more modern but hopefully will work fine too.
Amazingly fast shipping!

took old off, put new knob on, by hand

Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.

pulled it off, went to internet to see if I could find.
Did Find. Ordered and replaced.

Never really used the grill and needed 2 more burners so I just pulled out the grill assembly and plugged in the burner assembly, added the new pan cover and new grates and viola, I had a four burner stove. Still can pop the grill back in if needed. Much less expensive than buying a whole new cooktop.

One oven door hinge spring was broken. I ordered two hinges to complete the repair.
The repair could not have been easier. I removed the door from the oven an unscrewed the outer frame of the door from the inner door assembly. I unscrewed the old hinge assembly and replaced them with the two new hinges.
I set the door back on the oven and replaced the oven door retaining hardware.
After replacing the retaining hardware, I removed the temporary shipping pins that keep the spring assembly static. Very important: don’t remove these hinge pins until the door is on the oven an the oven retaining hardware is secured.

Repair is simple as long as you TURN OFF THE CIRCUIT BREAKER first. After that, take off the cover over the switches (pull knobs off, remove 2 screws and lift off the cover), pull the bad switch straight up off the gas valve, pull the two wires off the switch, plug them back onto the new switch, place it back over the gas valve stem, reassimble the cover and knobs, turn back on the circuit breaker, and verify that ignition switch works. Not a hard repair. (HINT: while you are waiting on the replacement part, you can light the bad burner by turning on the opposite burner ignition switch and using that "spark" to light the other burner.)

Remove oven door by removing chrome flat plate that holds the hinge in place (one screw at each hinge) and LIFT door off oven. There is a hole in the hinge that you can stick a small nail through to hold the hinge in the "partially open" position for easier removal and replacement of the door (I didn't know this until I received the new hinges, which have a removeable pin in the hole.) After door is off, remove three screws each, on the top and bottom of door, to remove the back half of door and expose the hinges. Remove one screw from bottom of door that holds bottom of hinge in place. Lift out hinge bottom and unhook top of hinge. Reverse process to reassemble. Remove small pins by opening oven door fully. The new hinges did solve the problem. You have to order two hinges for each door. They are NOT sold as pairs.

Removed the door then the end caps and inner panel then the hinge system and replaced with the one piece new set of hinges and back together done in 30 to 45 minutes The new parts were a perfect replacement.

Not a problem, very simple once I got all the parts I needed...operator at partselect was very helpful and nice to talk to...Thanks for the extra cooking space

We panicked cause even simple repairs on these products cost and cost.....but we remained calm and ordered the exact part necessary from you. It arrived in just 3 days and once we had the part in hand it was easy to understand how to replace it. We disassembled the door with screwdrive and swapped the broken part with the new one. The one gotcha was that we were not aware of the shipping pin holding the spring and we struggled for a few trying to get the door closed all the way. Once we discovered the pin and removed it, it was fixed and we were PLEASED!

Thank you,
Louise and Rickl